AMCI SMD34K Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 100

background image

C

OMMAND

D

ATA

F

ORMAT

SMD34K User Manual

ADVANCED MICRO CONTROLS INC.

64

Command Word 0

Figure R6.2 Command Word 0 Format

Bit 15: Mode_Select –

“0” for Command Mode programming.

It is possible to write configuration data to the unit using the output words, but the use of this
method is discouraged. Configuration data should be written to the SMD34K using the CoE
interface as described in the previous chapter.

Bit 14: Preset_Encoder –

When this bit makes a 0



1 transition, the unit will preset the Encoder Position to

the value stored in the

Position

double integer register defined by the ESI file.

Bit 13: Run_Assembled_Move –

When this bit makes a 0



1 transition, the unit will run the Assembled

Move already stored in memory.



Assembled_Move_Type – Command Word 1, Bit 9:

This bit determines the type of move

that is run. When this bit equals “0”, a Blend Move is run. When this bit equals “1”, a Dwell
Move is run. When starting a Dwell Move, the Dwell Time is programmed in word 9 of the
Command Data. The value is programmed in milliseconds and can range from 0 to 65,536.



Reverse_Blend_Direction – Command Word 1, Bit 4:

This bit is used to determine the direc-

tion that the Blend Move will be run in. When this bit equals “0”, the Blend Move runs in the
clockwise direction. When this bit equals “1”, the Blend Move is run in the counter-clockwise
direction.

Bits 12 & 11: Program_Assembled & Read_Assembled_Data –

These bits are used to program the seg-

ments of an Assembled Move before the move can be run. Their use is explained in the

Move Programming

section of this manual starting on page 38.

Bit 10: Reset_Errors –

When this bit makes a 0



1 transition, the unit will clear all existing command

errors and reset the

Move_Complete

bit in the Network Input Data. This bit does not clear a configu-

ration error or the

Position_Invalid

status bit. Reset_Errors will also clear a driver fault caused by

removing the main power while the auxiliary power remains.

Bit 9:

Preset_Position –

When this bit makes a 0



1 transition, the unit will preset the Motor Position. The

value depends on the state of the

Preset_To_Encoder

bit (Command Word 1, bit 13). If the

Preset_To_Encoder

bit equals “0”, the Motor Position is preset to the value stored in the

Position

double integer register defined by the ESI file. If the

Preset_To_Encoder

bit equals “1”, the Motor

Position is set to:



In either case, the

Move_Complete

and

Position_Invalid

bits in the Network Input Data are reset to “0”.

Bit 8:

Jog_CCW –

When this bit makes a 0



1 transition, the unit will run a Jog Move in the counter-

clockwise direction. The full explanation of a

CW/CCW Jog Move

can be found starting on page 32.



Registration_Move – Command Word 1, Bit 7:

When this bit equals “0”, and a Jog Move

command is issued, it will run as a standard Jog Move. When this bit equals “1” and a



Jog Move command is issued, the move will run as a Registration Move.

Command Word 0

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

Prst

_Enc

Run_A

M

ov

R

d_A

Dat

a

Pr

g_A

ss

m

RSet

_

Er

r

Pr

st_

P

os

Jog_CCW

Jog_CW

Hom

e_CCW

Ho

me_CW

I-

S

to

p

Re

sm

_M

v

Ho

ld_

M

v

Motor Position

Encoder Position

Motor Programmed Steps per Turn

Encoder Programmed Pulses per Turn

-------------------------------------------------------------------------------------------



=

«
...
62
63
64
65
66
...
»

Содержание SMD34K





































































































Отзывы:

Нет отзывов

Похожие инструкции для SMD34K

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Rain Bird Страницы: 138

Бренд: RADEMACHER Страницы: 68

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: SMC Networks Страницы: 15

COMBIVERT F4-S/1.2

Бренд: KEB Страницы: 96

Бренд: Waterbird Страницы: 19

MOBA-Matic MMC-1000

Бренд: MOBA Страницы: 172

Бренд: Vimar Страницы: 8

Бренд: Astrosyn Страницы: 7

SUNSAVER SS-10-12V

Бренд: Morningstar Страницы: 26

Бренд: NovaStar Страницы: 11

Бренд: Marmitek Страницы: 4

AutoMaXX Series

Бренд: MSA Страницы: 22

BNI EIP-502-105-R015

Бренд: Balluff Страницы: 274

Бренд: National Instruments Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды