AMCI NEXUS NX2A4E2 Скачать руководство пользователя страница 71

Страница: 71 / 76

20 Gear Drive, Plymouth Ind. Park, Terryville, CT 06786



Tel: (860) 585-1254 Fax: (860) 584-1973 http://www.amci.com

PROFINET Task

PROFINET N

ETWORK

ONFIGURATION

Basic Steps

Configuring a PROFINET host requires a few basic steps.

1) Download the ZIP archive that contains the GSDML files for the Networked Driver from the

www.amci.com website.

2) Install the GSDML file into the configuration software for your host controller.

3) Add the NX2A4E2 to the PROFINET Network.

4) Set the I/O word addresses used to communicate with the unit.

6.1 Download the GSDML files

The GSDML files are available on the AMCI website on the

http://www.amci.com/industrial-automation-

support/configuration-files/

web page. The file is a ZIP archive that has to be extracted to a folder on your

computer. Extracting the ZIP file will leave you with multiple files. One is the GSDML file and the others are
icon files for the various devices.

6.2 GSDML File Installation

1) Open or create a new project that

will include the NX2A4E2 and
open the Project View of the
project.

2) In the menu, select

Options ->

Manage general station
description files(GSD)

3) In the window that opens, click on

the [

...

] button and navigate to the

folder that contains the extracted
GSDML file you downloaded from
the AMCI website. Once at the
folder, click on the [

] button.

4) Click on the check box next to the

name of the GSD file and click on
the [

Install

] button. The system will

install the GSD file.

5) Click the [

] button and wait

for the software to finish installing
the file and updating the Hardware
Catalog.

6.3 Configure the PROFINET Network

A CPU must be added to the project and the PROFINET network must be configured before an NX2A4E2
can be added to the system.

Refer to Siemens documentation for information on configuring the PROFINET network to suit your applica-
tion.

This chapter outlines the steps commonly needed to get an NX2A4E2 communi-
cating with the PROFINET master. A Siemens SIMATIC S7-1212C controller is
used in this example.

Figure T6.1 GSD File Installation

Содержание NEXUS NX2A4E2













































































Результаты поиска

Содержание NEXUS NX2A4E2

Отзывы:

Похожие инструкции для NEXUS NX2A4E2

Бренды по названию

Популярные бренды

AMCI NEXUS NX2A4E2, Руководство пользователя

Результаты поиска

Содержание NEXUS NX2A4E2

Отзывы:

Похожие инструкции для NEXUS NX2A4E2

Бренды по названию

Популярные бренды