manualshive.com logo in svg

Ambirad AR13 SL, Руководство по установке и обслуживанию, Страница: 10 / 20

Поделиться
Скачать
Ambirad AR13 SL Скачать руководство пользователя страница 10

10

Figure 10 Condensate box arrangement

For double linear heaters refer to the relevant
SL data sheet. 

Effectively a DL heater comprises of two
identical SL heaters with the fan being
replaced by a condensate box and fan 
combined in one unit. 

Bracket positions, reflectors and turbulators
remain consistant with SL models. 

For total overall lengths and weights of DL
heaters refer to the table below. For damper
settings refer to the table on p11 section 11.

Installation should be carried out in the roof
space due to the length of the heaters. Refer
to the SL data sheet for bracket positions and
reflector installation.

Data is shown for all DL heaters.

Model

O/A length (m)

Total installed weight (kg)

SL data sheet reference

AR13 DL (22ft)

13.26

112

GB/AR/068/0901

AR22 DL (24ft)

15.0

128

GB/AR/069/0901

AR22 DL (27ft)

16.0

144

GB/AR/083/0603

AR22 DL (32ft)

19.0

170

GB/AR/084/0901

AR22 DL (36ft)

21.0

192

GB/AR/087/0901

AR35 DL (33ft)

20.0

184

GB/AR/070/0901

AR35 DL (42ft)

25.0

234

GB/AR/089/0103

AR35 DL (50ft)

30.0

280

GB/AR/093/0103

AR40 DL (42ft)

25.0

234

GB/AR/090/0103

AR40 DL (50ft)

30.0

280

GB/AR/094/0103

ARE13 DL (22ft)

13.26

112

GB/ARE/075/0901

ARE22 DL (27ft)

16.0

144

GB/ARE/076/0901

ARE35 DL (42ft)

25.0

234

GB/ARE/077/0901

ARE40 DL (42ft)

25.0

234

GB/ARE/078/0901

10 AR and ARE series double linear

gas radiant tube heaters

Damper vertically up

Figure 11 Typical double linear arrangement

 

Содержание AR13 SL





















Отзывы:

Нет отзывов