background image

 

 

5. LED Indications

 

BEHAVIOUR 

MEANING 

  Permanently switched on 

  GNSS signal is not received 

  Blinking every second 

  Normal mode, GNSS is working 

  Off 

  GNSS is turned off because:  Device is not working or    
  Device is in Sleep mode      

  Blinking fast constantly 

  Device firmware is being flashed 

                         

 

BEHAVIOUR 

MEANING 

Blinking every second 

Normal mode 

Blinking every two seconds 

Sleep mode 

Blinking fast for a short time  Modem activity 

Off 

Device is not working or Device is in Boot mode 


 

6. Safety information 

 

This  message  contains  information  on  how  to  operate  safely.  By  following  these 
requirements and recommendations, you will avoid dangerous situations. You must read 
these instructions carefully and follow them strictly before operating the device! 

 

 The  device  uses  SELV  limited  power  source.  The  nominal  voltage  is+12  V  DC.  The 

allowed voltage range is +10…+30 V DC. 

 

 To  avoid  mechanical  damage,  it  is  advised  to  transport  the  device  in  an  impact-proof 

package.  Before  usage,  the  device  should  be  placed  so  that  its  LED  indicators  are 
visible. They show the status of device operation. 

 

 When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the 

vehicle power supply should be disconnected.

 

 

 Before  unmounting  the  device  from  the  vehicle,  the  2x6  connector  must  be 

disconnected. The device is designed to be mounted in a zone of limited access, which 
is  inaccessible  to  the  operator.  All  related  devices  must  meet  the  requirements  of  EN 
62368-1 standard. The device is not designed as a navigational device for boats.

 

 

Do  not  disassemble  the  device. If  the  device  is  damaged,  the  power  supply  cables  are  not 
isolated or the isolation is damaged, DO NOT touch the device before unplugging the power 
supply. 

 

All  wireless  data  transferring  devices  produce  interference  that  may  affect  other  devices 
which are placed nearby. 

 

 The device must be connected only by qualified personnel. 

 

 

 The device must be firmly fastened in a predefined location. 

 

 

The programming must be performed using a PC with autonomic power supply. 

 

Содержание AMB375











Отзывы: