background image

 

 

 

Maintenance, repair and care 

 

 

68

  

EK-S/EK-SH  BAG0022.4  07.22

 

 

12.5 

Hydraulic system 

 

WARNING 
Danger due to escaping high-pressure hydraulic fluid which can 

penetrate the body through the skin (danger of infection). 

 

Only a specialist workshop may carry out work on the hydraulic 

system. 

 

The hydraulic system is under high pressure. Depressurise the 

hydraulic system before carrying out work on the hydraulic sys-

tem. 

 

When searching for leak points, always use suitable aids. 

 

Never attempt to plug leaks in hydraulic hose lines using your 

hand or fingers. 

    Escaping high pressure fluid (hydraulic fluid) may pass through 

the skin and ingress into the body, causing serious injuries!  

    If you are injured by hydraulic fluid, contact a doctor immediate-

ly. Risk of infection! 

 

 

WARNING 
Danger of unintentional contact with hydraulic fluid! 

Please take the following first-aid measures: 

 

Following inhalation: 

ο

 

No special action required. 

 

Following contact with the skin: 

ο

 

Wash off with plenty of soap and water. 

 

Following contact with the eyes: 

ο

 

Rinse eyes for several minutes under running water, hold-

ing the eyelid open. 

 

Following ingestion: 

ο

 

Seek medical assistance. 

 

Содержание EK-S 150













































































Отзывы: