Amazone GHS 1500 Drive SmartCut Скачать руководство пользователя страница 87

Страница: 87 / 138

Application area

100%

cutting

blades and

scarifying

blades,

combined

50%

cutting

blades and

scarifying

blades,

combined

50% long

flail blades

H77,

ground and

scarifying

blades,

combined

100% long

flail blades

H60,

ground and

scarifying

blades,

combined

100% long

flail blades

H77,

ground and

scarifying

blades,

combined

Selection of the

thickness of the

scarifying blades in

combination with the
flail blades or cutting

blades, depending on

the application area

Scarifying

blade 2 mm

Scarifying

blade 3 mm

= Very good results

= Good results

6.9.5 Selecting the blade equipment for scarifying

IMPORTANT

Implement damage due to different
scarifying blades

Imbalance on the rotor

Only equip the rotor with one type of
scarifying blade.
Make sure that you have the right blade
combination and arrangement for your
application area.

When scarifying, a distinction is made between wide
scarifying and narrow scarifying.

Wide scarifying, blade spacing 51 mm.

Narrow scarifying, blade spacing 17 mm.

For wide scarifying,

install the scarifying blades

at a spacing of 51

mm, see page 82.

This enables deeper action without being too
aggressive on the sward.

When installing the blades

, pay attention to

the marking for the first row.

51 mm

CMS-I-00003727

CMS-T-00005200-A.1

6 | Preparing the machine

Preparing the implement for operation

MG6212-EN-II | C.1 | 12.04.2021

Содержание GHS 1500 Drive SmartCut











































































































































Результаты поиска

Содержание GHS 1500 Drive SmartCut

Отзывы:

Amazone GHS 1500 Drive SmartCut, Оригинальное руководство по эксплуатации, Страница: 87 / 138

Результаты поиска

Содержание GHS 1500 Drive SmartCut

Отзывы: