background image

Page 3 

TCX-22 Amano 

Cincinnati, 

Inc. 

Power Options 

The TCX-22 can be powered by either an AC Adapter or a 12 volt 
Sealed Rechargeable battery. The Battery Power Switch on the base 
enables you to turn the Battery Power ON or OFF. The battery is 
equipped to maintain normal operations for 1 week and/or 5000 prints in 
the event of an A/C power failure. 

Installing the 12 Volt Battery 

1.

Remove the AC Adapter if equipped 
and remove the cover.

2.  Lay the unit down clock face up 
3.  Remove left battery bracket screws 

4.

Pull out the left battery bracket.

5.

Carefully insert the battery with the 
positive and negative clips facing 
outwards and to the right.

6.

Install the left battery bracket

7.

Observing polarity, attach the “Red” 
Positive female wire harness to the 
“Red” (+) Positive male connector on the Battery. 

8.  Attach the “Black” Negative female  harness wire to the “Black” (-) 

Negative connector located on the battery. 

9.  Set the Battery Power to the “Connected” position. 

Note: 

Recharge the battery at least every two weeks or every 5000 

prints. The minimum charging time should be 12 hours and the switch 
should be turned off when the unit is not in use. 

Connecting the AC Adapter

1.  Set the Battery Power Switch to the OFF position. 
2.  Verify that the AC outlet voltage falls in the range of 100-240 Volts 

AC. Verify that the cord and plug are appropriate for your AC source. 

3.  Plug the connector end of the AC Adapter into the Power Connector 

and the other end into a properly grounded 120 or 240 Volt outlet. 

Содержание TCX-22





















Отзывы: