Amana RCS10A Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

Amana RCS10A Скачать руководство пользователя страница 23

5-5

F. MAGNETRON REMOVAL

1) Disconnect the leadwire from the magnetron.

2) Carefully remove the mounting screws holding the

magnetron and the waveguide.

3) Remove the magnetron ASS’Y until the tube is

clear from the waveguide.

NOTE:
1. When removing the magnetron, make sure its

dome does not hit any adjacent parts, or it may be
damaged.

2. When replacing the magnetron, be sure to install

the magnetron gasket in the correct position and be
sure that the gasket is in good condition.

3. After replacing the magnetron, check for microwave

leakage with a survey meter around the
Microwave energy must be below the limit of 5
mW/cm

2

. (With a 275 ml. water load).

Make sure that gasket is rigidly attached to the
magnetron. To prevent microwave leakage, tighten
the mounting screws properly, making sure there is
no gap between the waveguide and the magnetron.

G. REMOVING THE STIRRER
FAN MOTOR

1) Disconnect the leadwire from the stirrer fan motor

terminals.

2) Remove the screw securing the stirrer fan motor to

the oven cavity ASS’Y

3) After repairing the motor, replace the removed

leadwire.

NOTE:
1. Remove the wire lead from the stirrer fan motor

VERY CAREFULLY.

2. Be sure to grasp the connector, not the wires, when

removing.

Magnetron

Stirrer fan motor

«
...
21
22
23
24
25
...
»

Содержание RCS10A













































Отзывы:

Нет отзывов