Amana Menumaster RCS511A Скачать руководство пользователя страница 14

Страница: 14 / 45

4-8

PROGRAMMING

Preprogrammed Number Pads

Oven has 10 preprogrammed number pads. Follow
instructions below to program heating times and power
levels for customized cooking.

1. Open oven door.

¥ If door is closed or STOP/RESET pad is pressed

before finishing programming sequence, oven exits
programming mode.

2. Press and hold pad 1 for approximately 5 seconds.

¥ After 5 seconds, signal sounds. Display shows

ÒPROGRAMÓ indicating program mode..

3. Press desired number pad.

¥ Display shows heating time, ÒCOOK LEVELÓ and

power level if other than 100 percent power.

4. Press number pads to enter desired cooking time.

¥ For example, to heat for 2 minutes 30 seconds,

press 2, 3, and 0 pads.

5. Press desired power level pad to change power level.

¥ If a power level pad is not pressed, oven defaults to

100% power.

¥ For example, pressing MEDIUM 50% pad sets oven

to 50% power.

¥ Display shows current power level if other than 100%

power.

6. Press START pad to save new heating time and

power level in oven memory.
¥ Repeat step 3-6 to program additional pads.

7. Press STOP/RESET pad or close oven door to exit

programming mode.

Multiple Heating Stages

Follow instructions below to program oven to perform 3
consecutive heating cycles without interruption.

1. Open oven door.

¥ If door is closed or STOP/RESET pad is pressed

before finishing programming sequence, oven exits
programming mode.

2. Press pad 1 for approximately 5 seconds.

¥ After 5 seconds, signal sounds.

3. Press desired number pad.

¥ Display shows heating time and preprogrammed

number.

4. Press number pads to enter desired cooking time.

¥ For example, to heat for 2 minutes 30 seconds,

5. Press desired power level pad to change power level.

¥ If a power level pad is not pressed, oven defaults to

100% power.

¥ For example, pressing MEDIUM 50% pad sets oven

to 50% power.

¥ Display shows current power level if other than 100

percent power.

6. Press TIME ENTRY pad

¥ Display briefly shows ÒSTAGE 2Ó . Then cook time

and power level for stage show in display.

¥ Repeat steps 5-6 to create additional stages.

7. Press START pad to save new heating time and

power level in oven memory.

8. Press STOP/RESET pad or close oven door to exit

programming mode.

Содержание Menumaster RCS511A














































Результаты поиска

Содержание Menumaster RCS511A

Отзывы:

Похожие инструкции для Menumaster RCS511A

Бренды по названию

Популярные бренды

Amana Menumaster RCS511A, Руководство по обслуживанию

Результаты поиска

Содержание Menumaster RCS511A

Отзывы:

Похожие инструкции для Menumaster RCS511A

Бренды по названию

Популярные бренды