background image

4

Location Requirements

IMPORTANT:

 Observe all governing codes and ordinances.  

Do not obstruct flow of combustion and ventilation air.

 

It is the installer’s responsibility to comply with installation 

clearances specified on the model/serial rating plate. The 

model/serial rating plate is located on the left side of the 

bottom of the broiler.

A.  Model/serial rating plate location

 

The range should be located for convenient use in the 

kitchen.

 

Recessed installations must provide complete enclosure of 

the sides and rear of the range.

 

To eliminate the risk of burns or fire by reaching over heated 

surface units, cabinet storage space located above the 

surface units should be avoided. If cabinet storage is to be 

provided, the risk can be reduced by installing a range hood 

that projects horizontally a minimum of 5" (12.7 cm) beyond 

the bottom of the cabinets.

 

All openings in the wall or floor where range is to be installed 

must be sealed.

 

Do not seal the range to the side cabinets.

 

Cabinet opening dimensions that are shown must be used. 

Given dimensions are minimum clearances.

 

The anti-tip bracket must be installed. To install the anti-tip 

bracket shipped with the range, see “Install Anti-Tip Bracket” 

section.

 

Grounded electrical supply is required. See “Electrical 

Requirements” section.

 

Proper gas supply connection must be available. See “Gas 

Supply Requirements” section.

 

Contact a qualified floor covering installer to check that the 

floor covering can withstand at least 200°F (93°C).

 

Use an insulated pad or ¼" (0.64 cm) plywood under range  

if installing range over carpeting.

IMPORTANT:

 To avoid damage to your cabinets, check with 

your builder or cabinet supplier to make sure that the materials 

used will not discolor, delaminate, or sustain other damage. This 

oven has been designed in accordance with the requirements 

of UL and CSA International and complies with the maximum 

allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured 

Home Construction and Safety Standard, Title 24 CFR, 

Part 3280 (formerly the Federal Standard for Mobile Home 

Construction and Safety, Title 24, HUD Part 280). When such 

standard is not applicable, use the Standard for Manufactured 

Home Installations, ANSI A225.1/NFPA 501A, or with local 

codes.

Mobile home installations require:

 

When this range is installed in a mobile home, it must be 

secured to the floor during transit. Any method of securing 

the range is adequate as long as it conforms to the 

standards listed above.

Product Dimensions

A.  36" (91.4 cm)
B. 29

7

8

" (75.9 cm)

C. 25

7

64

" (63.8 cm)

D. 47

5

64

" (119.6 cm)

A

B

A

C

D

Содержание AGR4230BAW

















Отзывы: