ALVEO3D 526563 Скачать руководство пользователя страница 3

Страница: 3 / 36

SAFETY INSTRUCTIONS

Read safety instructions before use

3D printer enclosures contain harmful emissions from 3D
printing. It is advised to always turn the filtering system on
during the printing process.

The filtering system is powered by a high-pressure fan. Do not
turn on the fan before full assembly done with the protective
grid and the P3D filter. Failure to comply with this instruction
can cause injuries.

Please use recommanded electrical voltages to power electronic
board, as indicated in the assembly instructions to prevent
damage.

Do not touch the electronic board in operation.

Make sure the Printercase does not interfere with the full
motion of your 3D printer axis, after it is placed in the enclosure.

Filter operational range 0-60°C max

Clean antidust grids with a moist cloth.

For cleaning inside the Printercase, wear single-use gloves.

Содержание 526563





































Результаты поиска

Содержание 526563

Отзывы:

Бренды по названию

Популярные бренды

ALVEO3D 526563, Инструкция по эксплуатации

Результаты поиска

Содержание 526563

Отзывы:

Бренды по названию

Популярные бренды