Alva GWH1012 Скачать руководство пользователя страница 14

2.Installation of pipes

(a).Connection of the cold water supply pipe:

      • The cold water inlet joint is G1/2 pipe thread.

      • The water inlet pipe must be connected by using metal tube, or by rigid water pipe.

      • The inner diameter of the inlet pipe (including the valve) shouldn’t be less than 8mm.

      • The cold water valve should be installed with the water inlet pipe.

      • Please ensure that the filter in the cold water inlet is mounted correctly. 

        Clean the new pipes by flushing with water. Make sure there are no blockages, then  

        insert the rubber gasket and fix the water inlet joint tightly.

(b).Connection of the hot water supply pipe:

      • The hot water outlet joint is G1/2 pipe thread.

      • The hot water outlet pipe must be connected by metal tube or by rigid water 

        pipe or by rubber pipe with sprayer directly.

      • The inner diameter of the hot water pipe outlet pipe (including the valve) shouldn’t be   

        less than 8mm.

(c). After installation, please open the cold water valve to the maximum to test the flow of 

      water and check whether there is water leakage.

(d). Installation of the gas supply pipe:

      • The gas inlet joint has a G1/2 pipe thread. Make sure that the gas inlet pipe joint and 

         rubber gasket is connected. The special soft rubber tube can be used according to the 

         technical parameters. Securely fit the pipe with the clip. Note: Gasket must be inserted, 

        otherwise you will experience a gas leak.

      • After the gas inlet joint is connected, open the gas supply valve, and check whether 

        there is a gas leak at the joint with soapy water.

      • Liquified petroleum gas users should use a good quality low pressure adjusting valve    

        with a flux above 0.6m/h.

3.Installation of exhaust device:

(a) According to the outline dimension of the attached flue pipe, make a hole with the

     diameter a little larger then the flue pipe at a suitable position to easily install the flue pipe

     horizontally easily.

(b) The installation of the flue is shown in the

      Drawing 10. The total height of the exhaust pipe

      should be more than 2.3 meters and the

      horizontal length must not exceed 3 meters.

      There must be a vertical ascending flue pipe and

      the hole should not be less than 250mm above

      the exhaust pipe cover. The gap between the

      flue pipe and the hole should not be filled with

      cement, otherwise repairs will be difficult.

(c) Install an exhaust fan not lower than the top of the

     water heater.

11

Содержание GWH1012
























Отзывы: