ENGLISH
1.
DESCRIPTION
The lamp is specifically designed to warn (alarm) about the move-
ment of the automated doors, gates and barriers.
2.
FEATURES
•
Operation mode with or without flashing.
•
Built-in antenna.
•
Mounting on horizontal or vertical surface.
•
Possibility to install outdoors.
3.
TECHNICAL SPECIFICATIONS
Supply voltage .............................................................................. AC-DC 12 … 230 V
Maximum power consumption ..........................................................................3 W
Housing protection degree ................................................................................. IP54
Working temperature range ...........................................................− 20 … + 60 ° С
Connected wire section .....................................................................max 1.5 mm2
Dimensions (not more than) ................................................140 × 145 × 65 mm
Lamp weight (net) ...............................................................................................0.19 kg
Lamp weight (gross) ..............................................................................................0.3 kg
Y
The specifications above apply at the ambient temperature
of 20 ° С (± 5 ° С).
4.
MOUNTING
Prior to mounting the lamp, make sure that the installation location
complies with the following conditions:
•
good visibility of the lamp at the required distance from inside
and outside;
•
position and surface chosen for lamp installation is both stable
and provides protection from impact;
•
easy access for maintenance.
The design of the lamp allows for mounting it directly on a horizontal
surface. Mounting on a vertical surface requires the use of a bracket
(supplied).
Partially or fully unscrew 4 screws of the lamp housing and extract
the base with the board mounted on it, to access the lamp connec-
tion socket and the antenna connection socket. Unscrew the board
from the base.
Before installation of the lamp determine the installation side. Then
drill (make) holes in the base for lamp screws and wire inlets.
Put the antenna wires and cables through the wall mounting
bracket, if it is used. Screw the bracket to the wall using the sup-
plied fittings. Put the wires through the lamp housing base with a
sealing plug. Fasten the base on the bracket with 2 screws. Connect
the corresponding wires to the board terminals
CN1
and
CN2
. Set
the lamp operation mode using the bridge
JP1
(
fig
.). For a flashing
lamp—the bridge (jumper) is installed (
FLASH
), for no flashing—the
bridge (jumper) is removed (
NO FLASH
). Fasten the board onto the
lamp housing base. Put the lamp housing glass with frames on the
installed base. Tighten 4 screws. For mounting pictures, see figure.
5.
STORAGE, TRANSPORTATION
AND DISPOSAL
The product shall be stored in its packaging in closed dry rooms,
at an air temperature 0 … + 25 ° С and relative humidity of are not
more than 80 %, and the air shall be free from acid, alkali and other
aggressive admixtures. Keep away from atmospheric precipitation
and direct sunlight. Shelf-life is 2 years from the manufacture date.
Transportation can be performed using all types of covered ground
vehicles, fitted with the means to prevent shock and movement
inside the vehicle.
Disposal is to be performed in accordance with the
current waste processing and disposal regulations ap-
plicable in the country of the Customer. The product
does not contain precious metals and substances that
pose a threat to life, human health or the environment.
Operation life—5 years.
Operating
manual
SL-U SERIES
SIGNAL LAMP
12-240 V
AC-DC
JP
1
CN
1
CN
2
JP1
NO FLASH FLASH
6.
WARRANTY OBLIGATIONS
The warranty on the operation capacity of the product is provided if
the storage, transportation and maintenance operations are carried
out according to the set regulations. The warranty period is three
years. Under the warranty, the service department only eliminates
malfunctions caused by the fault of the Manufacturer.
Note
:
the parts replaced under the warranty are considered the pro perty
of the service department that carried out the product repair.
The warranty does not apply in the following cases:
•
violation of use and storage regulations;
•
alterations performed by unauthorised persons, damage of the
products caused by the consumer or third parties;
•
damage caused by water ingression within the device;
•
force majeure (fires, lightning strikes, floods, earthquakes and
other natural disasters);
•
fully completed manual is not provided.
For questions about the service please contact the organization
that carried out the installation of the equipment.
7.
STATEMENT OF COMPLIANCE
Copies of declarations of compliance can be found at:
http://www.alutech-group.com/en/products/other/automatics/
documents
Made in China
Manufacturer
: ‘Hangzhou Hiland Technology Co., Ltd’
4th Building, 2 Xiyuanwu Road, Westlake Technology Garden,
Hangzhou, China +86 571 81958376
Importer to the Republic of Belarus / Authorised representa-
tive
: Alutech Systems s.r.o., 348 02, Czech Republic, Bor u Tachova,
CTPark Bor, Nova Hospoda 19, D5-EXIT 128,
phone / fax: + 420 374 6340 01,
e-mail: [email protected]
