- 2 -
Trove SALTO ULXB Kits Installation Guide
Overview:
Altronix Trove SALTO kits are pre-assembled and consist of Trove1SA1 or Trove2SA2 enclosure/backplane with factory installed Altronix power
supply/charger(s) and sub-assemblies. These kits also accommodate various combinations of SALTO modules for up to twelve (12) doors in a
single enclosure.
Configuration Chart:
Altronix
Model Number
115VAC 60Hz Input Current (A)
Power Supply Board Input Fuse Rating
Power Supply Board Battery Fuse Rating
Nominal DC Output Voltage
Maximum Supply
Current for Main and
Aux. Outputs on Power
Supply board and ACM4/
ACM8 Access Power
Controller’s outputs
Fail-Safe/Fail-Secure or Dry Form “C” Outputs
Current Per ACM4/ACM8 Output
(A)
ACM4/ACM8 Board Input Fuse Rating
ACM4/ACM8 Board Output Fuse Rating
PDS8 Board Input Fuse Rating
PDS8 Board Output Fuse Rating
Power
Supply 1
Power
Supply 2
Output
Range
(VDC)
Output
Range
(VDC)
T1SAK34
3.5
5A/
250V
N/A
20.19-26.4
–
24VDC @ 5.6A
4
2.5
10A/
32V
3A/
32V
10A/
32V
3A/
32V
T2SAK78
4.2
5A/
250V
15A/
32V
20.17-26.4
–
24VDC @ 9.2A
8
2.5
10A/
250V
2.5A/
250V
10A/
32V
3A/
32V
T2SAK7512
6.8
5A/
250V
15A/
32V
20.17-26.4
10.03-
13.2
12VDC @ 9.3A
24VDC @ 9.2A
12
2.5
10A/
250V
2.5A/
250V
10A/
32V
3A/
32V
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane(s) from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the
tamper switch bracket onto the edge of the enclosure approximately 2” from the right side
(Fig. 1, pg. 2)
. Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device. To activate alarm signal open the
door of the enclosure.
4. Mount SALTO modules to TSA2 backplane, refer to
pg. 3, 4, 5
.
5. Refer to the
ULXB Power Supply/Charger Installation Guide
for AL600ULXB, AL1012ULXB,
AL1024ULXB2 and corresponding
Sub-Assembly Installation Guides
for
ACM4, ACM8, PDS8, VR6 for further installation instructions.
Hardware:
Fig. 1
Tamper Switch
(included)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
Nylon Spacer | 5/16” Pan Head Screw | Lock Nut
