- 1 -
ReServ4WPV
Overview:
ReServ4WPV Video Surveillance UPS unit is designed to provide power for 24VAC and 12VDC cameras during normal or power
outage conditions. True sine wave regulated AC outputs and/or regulated DC outputs.
Specifications:
Stand-by Specifications:
Stand-by Batteries
4A (100VA) load at 24VAC and 1A load at 12VDC max.
Two (2) 12VDC/7AH
45 minutes
Two (2) 12VDC/12AH
90 minutes
Installation Instructions:
This installation should be made by qualified service personnel and should conform to the National Electrical Code and all local codes.
This product contains no serviceable parts.
1. Remove back plate inside the enclosure by removing four (4) mounting screws.
2. Mark and drill desired knockouts on the enclosure to facilitate
wiring
(Fig. 1, pg. 1).
Note: It is required to use UL Listed outdoor rated conduit hubs with a
minimum outdoor rating of NEMA4X.
3. Secure back plate inside the enclosure with four (4) mounting screws.
4. Mount unit in the desired location with the appropriate fasteners utilizing
the holes on the flanges (pg. 8). Secure enclosure to earth ground.
Note: This product needs to be secured to the building/pole
before operation.
5. Connect AC power mains to the terminals marked [L] and [N] (Fig. 2, pg. 3).
Connect ground wire to ground lug (Fig. 2, pg. 3).
Use 18 AWG or larger for all power connections (Battery, output)
(Fig. 2, pg. 3).
Use 18 AWG to 22 AWG for power-limited circuits
(AC Fail/Low Battery reporting) (Fig. 2, pg. 3).
Note: A readily accessible disconnect device shall be incorporated in the
building installation wiring.
6. The LEDs on the power supply board will illuminate when AC power is present.
7. Measure output voltage before connecting cameras/devices to outputs. This helps avoiding potential damage.
8. Connecting Fluidmesh Wireless Radio/Bosch Autodome:
Connect 12VDC Fluidmesh Wireless Radio to the terminals marked [P 1-2, N 1-2] (Fig. 2, pg. 3).
Connect 24VAC Bosch Autodome to the terminals marked [15-16] (Fig. 2, pg. 3).
9. Connect batteries to the terminals marked [+ BAT –] (Fig. 2, pg. 3). Use two (2) 12VDC batteries connected in
series for 24VDC operation (battery leads included).
Use batteries - Casil CA1270 (12V/7AH), Genesis NP7-12 (12V/7AH), Ultratech UT1270 (12V/7AH).
10. Connect appropriate signaling notification devices to AC FAIL and BAT FAIL (Fig. 2, pg. 3) supervisory relay outputs.
11. The power LEDs on the unit for Outputs 1-2 and 15-16 will illuminate when AC power is present (Fig. 2, pg. 3).
Note: If any of the power LEDs are not illuminated, the cause may be due to the following:
a. AC mains and battery fail.
b. One (1) or more power output PTCs are tripped due to a short circuit or overload condition.
c. Unit damaged/defective.
Input:
• 220VAC (working range 198VAC - 256VAC), 50/60Hz, 2.0A.
Output:
• PTC protected auto-resettable outputs:
- 24VAC @ 4A max.
- 12VDC @ 1A.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switchover to stand-by battery when AC fails.
Supervision:
• AC fail and low battery supervision (form “C” contacts).
Visual and Audio Indicators:
• AC/DC power LED indicators.
Visual Indicators:
• Individual power output LED indicators.
• Low voltage input and Shutdown LED indicators.
Additional Features:
• True sine wave regulated AC outputs and
regulated DC outputs.
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates costly labor.
Enclosure Dimensions:
• NEMA4 / IP66 Rated enclosure accommodates up to
two (2) 12VDC/7AH batteries.
17.375” x 12” x 6.5” (441.3mm x 304.8mm x 165.1mm).
ReServ4WPV
Outdoor Video Surveillance UPS
Right Panel
Left Panel
Suggested Locations
for Wire Entries
Bottom Panel
Fig. 1
