Overview:
These Altronix Rack Mount CCTV Power Supplies provide 24VAC or 28VAC distributed via eight (8) fuse or PTC pro
tected outputs for powering CCTV cameras, heaters, and other video accessories.
Rack Mount Configuration Reference Chart:
Altronix
utput Voltage
otal Output Current
umber of Outputs
TC Protected Outputs lass 2 power-limited r Dry locations, ass 3 for Wet locations)
use Protected
uto-resettable)
ass 1 Outputs
dividual Output Current ax per output - not to ceed total output current)
use Ratings
imary In-line
5VAC 50/60Hz put Current
gency stings
Model Number
O (VAC)
T (Power)
N
P (C fo Cl (a
F Cl
In (m ex
F
Pr Fuse Ratings
11 In
A Li
R248UL
24VAC
3.5A
8
–
Yes
3.5A
3.5A
3.5A/
250V
0.85A
28VAC
3A
R248ULCB
24VAC
3.5A
8
Yes
–
2.5A
–
3.5A/
250V
0.85A
28VAC
3A
Specifications:
Agency Listings:
• UL Listed for Commercial
Closed-Circuit Television Equipment (UL2044).
CUL Listed - CSA Standard C22.2 No.1-98, Audio,
Video and Similar Equipment.
• CE European Conformity
Output:
• 24VAC or 28VAC outputs.
• Surge suppression.
• Filtered and electronically regulated output.
• Short circuit and thermal overload protection.
Visual Indicators:
• Individual power LED indicators.
• Illuminated power disconnect circuit breaker
with manual reset.
Features:
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates
costly labor.
• Removable terminal blocks with locking screw flanges.
Rack Dimensions
(H x W x D)
:
• 2U rack mount chassis for use in standard EIA 19” rack.
3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm)
Installation Instructions:
1. Mount unit in the desired rack location (Space unit at least 3” from any video monitors), Do not obstruct side air vents.
2. Set power disconnect circuit breaker to OFF position (Fig. 1d, pg. 3).
3. All units are factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying power as follows:
Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and the yellow wire
[24V] is connected to the terminal marked [S].
Note: R248ULCB set for 28VAC operation is not Class 2 Rated, not power-limited.
4. Plug power cord into a grounded 115VAC 50/60 Hz receptacle (Fig. 1c, pg. 3), ground should be connected
as indicated in (Fig. 1e, pg. 3).
5. Set power disconnect circuit breaker to RESET (ON) position (Fig. 1d, pg. 3).
6. Measure output voltage before connecting devices. This helps avoiding potential damage. All terminals with
common suffix (P) “1P, 2P...” are the same polarity.
7. Set power disconnect circuit breaker to OFF position (Fig. 1d, pg. 3).
8. Connect devices to removable terminal blocks marked [1P & 1N] through [8P & 8N] for eight (8) output models
(Fig. 1a, pg. 3). Lock down the terminal blocks by tightening the screws on the flanges after the wiring
has been completed.
9. Upon completion of the wiring set power disconnect circuit breaker to RESET (ON) position (Fig. 1d, pg. 3).
10. Green power LEDs on faceplate will illuminate when power is present. When an output is in a trouble condition
(blown fuse or tripped PTC), the corresponding LED will not be illuminated (Fig. 1, pg. 3).
a. Blown fuse (R248UL) - Set power disconnect circuit breaker on back of unit to the OFF position (Fig. 1d, pg. 3).
Remove front faceplate to access fuses. Replace with fuses rated @ 3.5A/250VA (Altronix model # Fuse1).
- 2 -
R248UL Series
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
