HubWayLD Active Isolated Unit
- 3 -
6. Select 24VAC or 28VAC power output for Channels 1-8 (Channels 1-16) with the corresponding voltage
adjustment switches
(Fig. 1d, pg. 4)
.
7. Connect the BNC video outputs for HubWayLD8Di/LD16Di Channels 1 - 8 (Channels 1-16) to the
corresponding video inputs on the head end equipment (DVR)
(Fig. 1f, pg. 4)
.
8. Connect the RS422/RS485 output of the head end equipment (DVR) to the one (1) or both data input terminal
blocks of the HubWayLD8Di or HubWayLD16Di unit (polarity must be observed)
(Fig. 1e, pg. 4)
.
Note:
The Data input terminals of the HubWayLD8Di or HubWayLD16Di must be wired in parallel for proper
operation. When using fixed cameras disregard this step.
9. Connect Video Balun/Combiner at camera 1 to the HubWayLD8Di or HubWayLD16Di unit utilizing CAT-5 or
higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked
[Channel 1] of the HubWayLD8Di/LD16Di
(Fig. 1a, pg. 4)
. Plug the RJ45 connector at the opposite end of the
structured cable into the RJ45 jack of the Video Balun/Combiner located at camera 1.
• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner
(Figs. 2a, 2b, pg. 5)
.
• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner
(Figs. 2c, 2d, pg. 5)
.
Repeat steps 6-9 for each additional camera (Channels 2-8 or Channels 2-16).
Note:
When a particular camera exceeds the maximum distance for power transmission, a local
external power source is required. Optionally, an Altronix HubSat4Di Passive UTP Transceiver Hub with Integral
Camera Power may be utilized
(Fig. 4a, pg. 6)
.
The combined total cable distance must not exceed 3000 ft. for video transmission between the
HubWayLD8Di/LD16Di and each camera routed through the HubSat4Di.
10. Set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Fig. 5, pg. 7)
and measure the
output voltage at the power output of each Video Balun/Combiner
(Figs. 2b, 2d, pg. 5)
before powering each camera
to insure proper operation and avoid possible damage.
• HubWayAv - Terminals marked [AC POWER]
(Figs. 2a, 2b, pg. 5)
.
• HubWayDv - Terminals marked [– 12VDC +]
(Figs. 2c, 2d, pg. 5)
.
11. Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final connections
(Fig. 5, pg. 7)
.
12. Connect the power outputs of the HubWayAv or HubWayDv Video Balun/Combiners to the power inputs
of the cameras
(Figs. 2a-2d, pg. 5).
Polarity must be observed.
13. Connect the terminals marked [+ DATA -- ] of the HubWayAv or HubWayDv Video Balun/Combiners to the data
terminals of the cameras for PTZ control
(Figs. 2a-2d, pg. 5)
. Polarity must be observed
.
When using fixed cameras disregard this step.
14. Connect the BNC connector of the HubWayAv or HubWayDv Video Balun/Combiners to the BNC video
outputs of the cameras
(Figs. 2a-2d, pg. 5)
.
15. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Fig. 5, pg. 7).
16. AC LED (Green) of the HubWayAv or DC LED (Red) of the HubWayDv Video Balun/Combiners will illuminate
indicating power is present at the cameras
(Fig. 2b, 2d, pg. 5).
17. The video signal indicator LEDs (Red) for Channels 1-8 of the HubWayLD8Di or 1-16 of the HubWayLD16Di will
illuminate when video signal is present
(Fig. 1i, pg. 4).
If any of these LEDs are not illuminated, there is no video
signal for that corresponding channel.
18. Optimize the picture quality for Channels 1-8 (Channels 1-16) by adjusting the corresponding potentiometer
marked [Picture]
(Fig. 1h, pg. 4).
19. Set gain for Channels 1-8 or Channels 1-16 by adjusting the corresponding potentiometer marked [Gain]
(Fig. 1h, pg. 4).
20. The power LEDs (Red) located on the front of the HubWayLD8Di/LD16Di for Channels 1-8 (Channels 1-16)
will illuminate when AC power is present
(Fig. 1c, pg. 4).
If all of the LEDs are OFF there
may be a complete loss of supply power to the HubWayLDi unit or the illuminated master power disconnect circuit
breaker is in the OFF position.
To restore the power output for HubWayLD8Di/LD16Di:
The PTC for that particular output is tripped.
1- Switch output voltage switch to the OFF position
(Fig. 1d, pg. 4)
to reset the PTC allowing approximately
1 minute before switching back to 24VAC or 28VAC.
2- Eliminate the trouble condition.
3- Switch output voltage switch back to the 24VAC or 28VAC position
(Fig. 1d, pg. 4)
.
