Altronix HubSat4DV, Руководство по установке, Страница: 5 / 8

HubSat4DV - 5 -
To restore the power output for HubSat4DV:
1 - Switch corresponding output voltage switch to the OFF position (Fig. 1d, pg. 4).
2 - Eliminate the trouble condition.
3 - Allow 1 minute for PTC to cool off.
4 - Switch output voltage switch to the 24VAC or 28VAC position as desired (Fig. 1d, pg. 4).
Alternate 24VAC fixed camera hookup (Fig. 6a, pg. 7).
After completing steps 1-5 from Installation Instructions Remote Accessory Module for use with HubWayV/
HubWayLDV/HubWayLDHV UTP Transceiver Hubs proceed with the following.
1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).
2. Connect one end of the coaxial cable to the BNC connector marked [Video1] of the HubSat4DV (Fig. 1a, pg. 4).
Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig. 6a, pg. 7).
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6), measure the
output voltage at terminal pair marked [AUX1] of the HubSat4DV to ensure proper operation and
avoid possible damage (Fig. 1b, pg. 4).
4. Connect the power output terminal pair marked [AUX1] to the power inputs of camera 1 (Fig. 1c, pg. 4).
Repeat steps 1-3 for each additional camera (Channels 2-4).
HubWayAv/HubWayAv2 passes AC voltage from pins
4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 5). HubWayDv/HubWayDvi converts AC voltage to DC
voltage from pins 4, 5, 7, 8 to terminals marked
[-- 12VDC +] (Fig. 3, pg. 5).
HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners:
Altronix
Model Number
Input Voltage
from HubWay
Unit Output Voltage to Camera Camera Type Power LED
HubWayAv *24VAC/28VAC *24VAC/28VAC *24VAC/28VAC Green
HubWayAv2 *24VAC/28VAC *24VAC/28VAC *24VAC/28VAC N/A
HubWayDv *24VAC/28VAC 12VDC 12VDC cameras Red
HubWayDvi *24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red
*Based on camera load and structured cable length.
VIDEO BALUN/COMBINER
CAT5 + DATA-- POWER
AC
VIDEO
HubWayAv
VIDEO
AC Power
to Camera
Data to
Camera
--
+
Data to
Camera
Green Power LED
12VDC Power
to Camera
+
--
Red Power LED
Wire
Connectors
RJ45 Jack RJ45 Jack
To BNC
Connector
of Camera
To BNC
Connector
of Camera
Structured
Cable from
HubWay8CD
or
HubWay16CD
Structured
Cable from
HubWay8CD
or
HubWay16CD
VIDEO BALUN/COMBINER
HubWayDv
CAT5 + DATA-- -- 12VDC+
--
+
Wire
Connectors
* Also Available as:
HubWayDvi
Video Balun/
Combiner
for non-isolated
12VDC cameras
Fig. 2
Fig. 2c Fig. 2a
Fig. 2b
Fig. 2e
HubWayAv2
Fig. 2d
Video from Camera
Data to Camera
Power to Camera
Cat5
back to
HubWay
or
HubSat