- 2 -
ALTV1224DC Series Installation Guide
Installation Instructions:
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 8)
. Secure enclosure to earth ground.
2. Slide switch to the OFF position
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5)
.
3. Set the unit to desired DC output voltage range by setting switch (SW1) on the power supply board to the
appropriate position
.
Use trimpot to adjust voltage if necessary
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5)
.
4. Connect the AC (115VAC, 50/60 Hz) to the terminals marked [L] and [N].
Connect earth ground
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5)
.
5.
Measure output voltage before connecting devices.
This helps avoiding potential damage.
6. Connect each DC device to the output terminals 1 through 8
(Fig. 1, pg. 3)
or
terminals 1 through 16
(Fig. 2, pg. 4 or Fig. 3, pg. 5)
.
Note:
Be careful to observe camera polarity.
7. When batteries are being used the DC output voltage must be adjusted by turning the trim pot VR1
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5)
clockwise to increase the output voltage to 13.7VDC for
12VDC operation and 27.1VDC for 24VDC operation.
Connect battery to the terminals marked [– BAT +] (battery leads included)
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5)
.
Use two (2) 12VDC batteries connected in series for 24VDC operation.
8. Slide switch to the ON position
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5)
.
9. Green LED on the PD8/PD8CB or PD16W/PD16WCB board will illuminate when power is present.
10. Upon completion of the wiring secure enclosure door with screws (supplied).
Input:
• Input 115VAC, 50/60Hz.
Output:
• Eight (8) or sixteen (16) fuse or
PTC protected outputs.
• 12VDC or 24VDC.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Filtered and electronically regulated outputs.
Features:
• AC input and DC output LED indicators.
• Power ON/OFF switch.
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates
costly labor.
E
nclosure Dimensions
(H x W x D approx.)
:
13.5” x 13” x 3.25”
(342.9mm x 330.2mm x 82.6mm).
Overview:
Altronix ALTV1224DC Series DC CCTV power supplies are designed to power CCTV Cameras and accessories.
Units provide 12VDC or 24VDC distributed via eight (8) or sixteen (16) fused or PTC protected outputs with a total
of 4A or 6A continuous supply current.
Eight (8) or Sixteen (16) Output ALTV1224DC Reference Chart:
Altronix
Model Number
115VAC
50/60Hz
Input
Current
Total
Output
Current
(Power)
Number
of
Outputs
PTC Protected
Auto-Resettable
Outputs
Fuse
Protected
Outputs
Output
Current
(max per
output)
ALTV1224DC
1.45A
4A
8
–
P
3.5A
ALTV1224DCCB
P
–
2.5A
ALTV1224DC1
16
–
P
3.5A
ALTV1224DC1CB
P
–
2.5A
ALTV1224DC2
2.5A
6A
–
P
3.5A
ALTV1224DC2CB
P
–
2.5A
Specifications:
