Altrex RS TOWER Safe-Quick 51, Инструкция по эксплуатации

Страница: 27 / 72

27
www.altrex.com
EN
6. Assembly
• Check that all parts, necessary tools and safety aids are present (e.g. helmet, gloves, safety shoes).
• Required tools:
- Rope
- Spirit level
• Assemble the components following the steps shown in appendix T4 and T5
• Make all the connections as shown in Annex T3
• See the table below for the reference to the annex with the configuration table and configurations per type of rolling tower
Configuration Attachment
RS TOWER 51/51+ T4
RS TOWER 52 T5
Configuration table and assemblies RS TOWER 51/51+ T6
Configuration table and assemblies RS TOWER 52 T7
Configuration table and assemblies RS TOWER 54 T8
Configuration table and assemblies RS TOWER 55 T9
RS TOWER 54/55 T10
6.1. Assembling the RS TOWER 51, 51+ and 52
A. Base section
Determine the working height you want to reach. See also annex T4 composition A (single width); annex T5 composition A (double width).
A1: Working height of an even number of metres A2: Working height of an odd number of metres
1. Start with a 4-rung frames (part B). 1. Start with a 7-rung frame (part A).
2. Put the wheels into the frames, put the brakes on and put them in
an outward direction [T3: F1 - F3].
2. Put the wheels into the frames, put the brakes on and put them in
an outward direction [T3: F1 - F3].
3. Place horizontal braces (part G) under the first rung on the vertical
[T3: F4 – F5].
3. Place horizontal braces (part G) under the first rung on the vertical
[T3: F4 – F5].
4. Place the 7-rung frames (part A) and lock them [T3: F6 - F8]. 4. Place the Safe-Quick® Guardrail(s) (part F) on the top rung with
the instruction label facing the inside[T3: F14 – F18].
5. Place the Safe-Quick® Guardrail(s) (part F) on the sixth rung with
the instruction label facing the inside [T3: F14 – F18].
5. Place the platform (part D) on the third rung of the 7-rung frames
[T3: F20 – F22].
6. Adjust the base section using a spirit level. 6. Adjust the base section using a spirit level.
7. Assemble the triangle stabilisers (part I) [T3: F9 – F13]. 7. Assemble the triangle stabilisers (part I) [T3: F9 – F13].
B1: Working height of an even number of metres B2: Working height of an odd number of metres
1. Place the Safe-Quick® Guardrail(s) (part F) on the top rung with
the instruction label facing the inside [T3: F14 – F18].
1. Access the temporary platform (part D).
2. Place the platform with trapdoor (part D) [T3: F19 – F22]. 2. Place the 7-rung frames (part A) and lock them [T3: F6 - F8].
3. Access the platform by going through the trapdoor. 3. Place the Safe-Quick® Guardrail(s) (part F) on the top rung with
the instruction label facing the inside [T3: F14 – F18].
4. Repeat the steps until you reach the required platform / working
height.
4. Place the platform with trapdoor (part D) [T3: F19 – F22].
5. Access the platform by going through the trapdoor.
6. Repeat the steps until you reach the required platform / working
height.
B. Middle section
See also T4 composition B (single width); T5 composition B (double width).
C. End section
See also T4 composition C (single width); T5 composition C (double width).
1. Place the toe board set (part J)
This manual described the composition that starts with installing the Safe-Quick® Guardrails. In addition to this composition, it is also
possible to start with diagonal braces (part H). For this purpose, replace the Safe-Quick® Guardrails of RS TOWER 51/51+ with two diagonal
braces for RS TOWER 51/51+ and with four diagonal braces for RS TOWER 52. See Annex T11 for these options.
Facade-free use
If necessary for the work to be carried out, the guardrails/Safe-Quick® Guardrail on the facade side of the working platform may be repositio -
ned. Only to be used if the distance to the facade is maximum 15 cm. Local legislation and regulations may contain supplementary measures on
top of this guide.