manualshive.com logo in svg

Alto L-20, Руководство оператора, Страница: 10 / 29

Поделиться
Скачать
Alto L-20 Скачать руководство пользователя страница 10

Page  -10-

    CLARKE TECHNOLOGY Operator's Manual -Encore S20/L20

Figure 8

Figure 9

Figure 10

How To Install The Batteries

The Encore machines uses two 12-volt batteries.  The
batteries are located in the battery compartment under
the recovery tank.

To install the batteries, follow this procedure:

  1. Turn machine off.  Set brake (if equipped).

 2. Make sure recovery tank is empty.

 3. Open recovery tank and secure with latch.

 4. Place the batteries in the tray as shown in

figure 8.

WARNING:

Lifting batteries without help
could result in an injury.  Get
help to lift the batteries.  The
batteries are heavy.

WARNING:

Working with batteries can
be dangerous.  Always wear
eye protection and protective
clothing when working near
batteries.  NO SMOKING!

  5. Connect the battery cables between batteries

and install long battery cable assembly as
indicated.  See figure 8.

 6. Join the connector from the battery pack to the

connector on the control panel.  See figure 9.

  7. Lower recovery tank.

 

NOTE:

Charge the batteries before using the
machine.

Battery Maintenance

The electrical power to operate the machine comes
from the storage batteries.  Storage batteries need
preventative maintenance.

WARNING:

Working with batteries can
be dangerous.  Always wear
eye protection and protective
clothing when working near
batteries.  NO SMOKING!

To maintain the batteries in good condition, follow
these instructions:

1.

Keep the electrolyte at the correct level.  The
correct level is between 1/4" below the bottom of
the tube in each cell and above the tops of the
plates.  Check the level of the electrolyte each
time you charge the batteries.  See figure 10.

How To Prepare the Machine For Operation

Correct Fill Line

(BATTERY NO. 40703A optional)

Содержание L-20






























Отзывы:

Нет отзывов