PHX LED Ellipsoidal
Installation & User’s Manual
PAGE 10
YOKE AND SHUTTER ASSEMBLY CONTINUED
YOKE & SHUTTER ASSEMBLY
Short Yoke
Position
Shutter Rotation
Lock Knob
Yoke Bolts
Cup Washers
Pivot Covers
T-Handles
Shutter Handle
Shutter Assembly
Lens Tube
USING SHORT YOKE POSITION
1. Remove T-Handle and its
2. associated hardware.
3. Remove yoke bolts, cup washers
and pivot covers. Note: use a 1/4:
hex head wrench to remove yoke
bolts.
4. Stretch yoke and snap it into short
yoke position.
5. Replace pivot covers, cup washers
and yoke bolts.
6. Replace T-Handle into square hole,
keeping the washer between handle
and yoke.
ROTATING SHUTTER ASSEMBLY
1. Loosen shutter rotation lock knob on either side of
the fixture.
2. Rotate shutter assembly 360° in either direction.
3. Tighten shutter rotation lock knobs to secure shutter
assembly.
4. To lock the shutters in place, rotate the Shutter Lock
Lever until proper tension is applied to shutters.
ADJUSTING YOKE
1. With one hand on ring handle to
hold unit, loosen T-Handle.
2. Tilt unit to desired angle.
3. Note: Reference angles have been
molded on the pivot cover to make
adjustments easier and more
precise.
4. Tighten T-Handle to secure fixture
in place.
INSTALLING C-CLAMP
The C-clamp is used to
mount the fixture to a
pipe hang position. The
C-clamp attaches to the
top of the yoke via the
1/2” bolt provided with
the C-clamp. Be sure to
keep the washer
between the bolt head
and the yoke.
***SHUTTER ASSEMBLY SCREW GUIDES
These two screws prevent the shutter assembly from coming off the light engine while rotating. On-
ly remove these screws when taking the light shutter assembly off of the light engine. After re-
placing the shutter assembly, replace these two screws to avoid injuries.
***Shutter Assembly Screw Guides
Installing C-Clamp:
1. Attach the C-Clamp to the top of the
yoke via the provided 1/2” bolt.
2. Keep the washer between the bolt
head and yoke.
3. Tighten the bolt using an adjustable
wrench or Altman Super Tool
Warning:
When mounting fixture a safety
cable is necessary to prevent injury in-
case the fixture becomes loose. Place the
safety cabe through the eyehole on the
top of the fixture and secure it around the
suporting structure.
Warning:
Supporting mechanism and structure must be capable of supporting the weight of the PHX LED
Ellipsoidal. For product technical information (including weight), refer to "TECHNICAL SPECIFICATIONS"
on page 19. Check applicable codes in your area for specific requirements.
ACCESSORY INSTRUCTIONS
ACCESSORY RETAINING LATCH
This unique retaining hatch is designed for pos-
itive locking and manual return.
1. Slide cover to right side.
2. Swing cover back.
3. Insert accessory.
4. Close cover. Make sure latch locks in
place.
DROP IN IRIS SLOT
This larger slot can accept either a drop-in iris
or a motorized pattern device (gobo rotator,
yo-yo etc). The slot has a retractable cover to
prevent light leak when not in use. When a
device is used, the cover should be closed to
the edge of the device placed in the slot.
When a drop-in iris is used, always place it so
the flat side is facing the shutters.
PATTERN PROJECTION
The pattern holder accepts standard ETC
Source 4 size pattern holders. The image of
the pattern can be rotated 360° in either
direction. The use of the donut will sharpen the
image.
INSTALLING SHUTTER PLATES
1. Pressure Plate (completely flat): Install
such that the tabs are on the top and
bottom and sides.
2. Iris and spring plate. Install so that the (4)
studs face the back of the unit.
SHUTTERS
1. The shutters are not removable without
dissembling the unit.
2. Care must be given to make sure each of
the four shutters stay in their proper
positions in between the shutter plates.
SOFT FOCUS LENS ADAPTER
The Soft Focus Lens Adapter is a pattern holder with a special holographic lens material. This
accessory allows the LED fixture to behave like a conventional ellipsoidal when using a soft focus.
When inserted in the gobo slot (iris slot for zoom lens), the matte side of the material should face
the light source and the shiny side should face the lens barrel.
NOTE:
To avoid damage to the
material do not add metal gobos in the same pattern holder.
ACCESORY INSTRUCTIONS
Accessory Retaining Latch:
This unique retaining hatch is designed for positive locking and
manual return.
1. Following label on accessory cover, slide cover to side and lift
up.
Note: Cover will be in LOCKED open position.
2. Insert desired accessory.
3. To close cover, you must
(a)
first move cover to side to
UNLOCK and
(b)
lower cover to original position.
Drop In Iris Slot:
This larger slot can accept either a drop in iris
or motorized pattern device (ie. gobo rotator). This slot has a
retractable cover in order to prevent light leak when not in use.
This cover should be closed as far as possible when the slot is in
use.
To avoid damage when in use always place the flat side
toward the shutters.
Soft Focus Lens Adapter:
The soft focus lens adapter is a pattern
holder with a special holographic lens material. This accessory
allows the LED fixture to behave like a conventional ellipsoidal.
When inserted into the gobo accessory slot the matte side of the
matterial should face the light source and the shiny side should
face the lens.
To avoid damage do not place metal gobos in
the same pattern holder.
LED Engine
Heat Sink location
Front Gate
Location
Removable Lens
Tube
