Congratulations on purchasing an Altizen Active Standing Desk,
and welcome to the world of active working.
SAFETY INSTRUCTIONS
2. Unplug from outlet before putting on or taking off parts.
3. Close supervision is necessary when this furnishing is used by,
or near children, invalids or disabled persons.
4. Use this furnishing only for its intended use as described in these
instructions. Do not use attachments not recommended by the
manufacturer.
5. Never operate this furnishing if it has a damaged cord or plug,
if it is not working properly, if it has been dropped or damaged,
or dropped into water. Return to a service center for examination
and repair.
6. Keep the cord away from heated surfaces.
7. Never operate the furnishing with the air openings blocked.
Keep the air openings free of lint, hair, and the like.
8. Never drop or insert any objects into any opening.
9. Do not use outdoors.
10. Do not operate where aerosol (spray) products are being used
or where oxygen is being administered
11. To disconnect, turn all controls to the off position, then remove
plug from outlet.
12.
WARNING:
Risk of injury – Keep children away from the desk.
13. For loading, always put heavier items towards the center and not
near the edges to help prevent the possibility of furnishing
tipping over.
14.
WARNING:
Risk of death of serious serious injury may occur
when children climb on equipment / furniture. Remote control or
toys placed on the furnishing may encourage a child to climb on
the furnishing and as a result the furnishing may topple over onto
the child.
WARNING
WARNING
GETTING STARTED
ALTIZEN GENERAL INFO
& SPECIFICATIONS
When using an electrical furnishing, basic precautions should always
be followed, including the following:
Read all instructions before using (this furnishing).
To reduce the risk of electric shock:
To reduce the risk of electric shock, always unplug this product
from the electrical outlet before cleaning.
1.
To reduce the risk of burns, fire, electric shock, or injury
to persons:
What’s Included
Your purchase includes:
·
1 Altizen Active Sit-Stand Converter
·
1 Handset Remote Control
·
1 AC/DC Adaptor with Power Plug
·
And if you have purchased a:
·
Single Monitor Version: 1 VESA Mount;
·
Dual Monitor Version: 1 Dual Bar with 2 VESA Mounts; or
·
Laptop Version: 1 Laptop Platform
In a double-insulated product, two systems of insulation are provided
instead of grounding. No grounding means is provided on a double-in-
sulated product, nor is a means for grounding to be added to the
product. Servicing a double-insulated product requires extreme care
and knowledge of the system, and is to be done only by qualified
service personnel. Replacement parts for a double-insulated product
must be identical to the parts they replace. A double-insulated product
is marked with the words: “DOUBLE INSULATION” or “DOUBLE
INSULATED.” The symbol is also able to be marked on the
product”
SAVE THESE INSTRUCTIONS
SERVICING OF DOUBLE-INSULATED PRODUCTS
Thank you for purchasing Altizen.
https://altizen.com
+65 6871 8885
If you have any questions, please contact us directly:
How to Assemble Your Desk
Watch Installation Video:
https://altizen.com/altizen-active-install
Base unit (and also applicable for all
other modules to do up the base version):
1. Place the base on your tabletop.
2. Place the pillar on top of the base
and secure the pillar onto the base
with the 3 pcs
M6x10
screws provided.
3. Slide the worksurface underneath
the sliding pillar base and secure
using the 5 pcs
M6x16
screws.
4. If you wish to, you can paste the
silicon cover over the screws to
hide them.
Assemble Your Modules and
Fix Your Screen Height
Single Monitor Mount
1. Sit in front of the sliding pillar and make a note of your eye level
height.
2. Count 2 hole spaces down from your eye level and align with the
top 2 screw holes of the single monitor VESA bracket. Secure with
the 4 pc
M5x12
screws.
3. Attach the VESA mount onto the back of your monitor.
4. Hook your monitor onto the VESA bracket and tighten the 2 screws
underneath.
Dual Monitor Mount
1. Sit in front of the sliding pillar and make a note of your eye level
height.
2. Count 2 hole spaces down from your eye level and align with the
top 2 screw holes of the dual bar. Secure with the 4pcs
M5x12
screws.
3. Attach the VESA mounts onto each of your monitors.
4. Hook each monitor onto the VESA brackets and tighten the 2
screws underneath.
5. To adjust the distance between the monitors, loosen the
thumbscrews at the top of the VESA bracket and slide your
monitors to the desired position, before tightening the screws
again.
Laptop Mount
1. Sit in front of the sliding pillar and make a note of your eye level
height.
2. Count 2 hole spaces down from your eye level and align with the
top 2 screw holes of the laptop platform. Secure with the 4pcs
M5x12
screws.
3. If you wish to, you can paste the silicon cover over the screws to
hide them.
Pairing and Using Altizen Active with your handset
remote control
1. Install the batteries into your handset.
2. Ensure the power is turned on for your workstation.
3. Within 15 seconds of turning the workstation on, press and hold
the “I” and “II” buttons at the same time until you see the blue LED
lights blinking. Let go, it will be paired.
4. You can move your desk through the handset using the “Up”
“Down” or set your own memory height using the Preset Height “I”
or “II” buttons.
5. To set your preferred standing height, press the “Up” button until
you reach your preferred standing height. Ergonomically, this
should be where your elbows would be bent at 90 degrees angle.
6. Save this height by pressing the “I” button for at least 3 seconds.
7. You can save a second preset height by pressing the “II” button for
at least 3 seconds.
8. Pressing each preset height button will bring it between the preset
standing height and base.
Help
Troubleshooting and assistance for your Altizen Workstation can be
found at https://altizen.com/FAQ
RETURN POLICY & WARRANTY
Warranty information and return policy can be found at
https://altizen.com/warranty and https://altizen.com/return-policy
respectively.
We reserve the right to change or modify any components of the
product, at any time without notice.
Size & Weight
Version
Height
(retrated)
Depth
Width
Weight
Height
(extended)
Base Model
73cm
65cm
80cm
26kg
94.5cm
Single Monitor
Model
73cm
65cm
80cm
26kg
94.5cm
Dual Monitor
Model
73cm
65cm
80cm
28kg
94.5cm
Laptop Model
73cm
65cm
80cm
28kg
94.5cm
Dimensions
Adjustable Height
460mm electrically actuated
Materials
Structure is made of powder-coated cold
rolled steel and worksurface is made of
medium density fibreboard
Weight
26 kg for the basic & single monitor, 28 kg
for the dual monitor & laptop versions
Connectivity
Radio Frequency
Moving Load Capacity
15kg
Static Load Capacity
15kg
Electronics
Line Voltage: Class II, 29VDC / 2A
Operating Temperature: 10°C to 35°C
Relative Humidity: 5% to 90%,
non-condensing
18.9"
(48cm)
19.7"
(50cm)
Max 37.2"
(94.5cm)
Max 18.1"
(46cm)
18.9"
(48cm)
31.5"
(80cm)
28.7"
(73cm)
25.6"
(65cm)
15.
WARNING:
Risk of injury – When moving the furnishing from up
to down or vice versa, do not place any parts of the body under
the furnishing and keep underside of furnishing clear of any
items that may obstruct the path. If any item obstruct the path,
use the remote control to move the furnishing up before removing
the item.
16.
WARNING:
Never attempt to lift the furnishing alone.
17. This desk operates at 29 V DC. It has a recommended maximum
weight capacity of 15kg. The furnishing is meant to operate
under environmental conditions ranging from 5-90% humidity
(non-condensing) and through an ambient temperature of
10 to 35°C.
18. Exceeding these limits can potentially damage the product and
void the warranty and/or result in injury to yourself or others.
DANGER
WARNING
1
