Altinex TNP327, Руководство пользователя

Страница: 1 / 9

TNP327 INTERCONNECT BOX User’s Guide
400-0704-004 1
Welcome!
We greatly appreciate your purchase of your TNP327 Series
Tilt 'N Plug. We are sure you will find it reliable and simple to
use. Superior performance for the right price, backed by solid
technical and customer support is what Altinex offers.
We are committed to providing Signal Management Solutions®
to our customers for the most demanding audiovisual
installations at competitive pricing and we welcome you to join
the ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your Tilt 'N Plug
Interconnect Box. Keep this manual handy for future reference.
These safety instructions are to ensure the long life of your
Tilt 'N Plug. and to prevent fire and shock hazards. Please read
them carefully and heed all warnings.
1.1 General
•
Unauthorized personnel shall not open the unit as there
are high-voltage components inside. Qualified Altinex
service personnel or their authorized representatives
must perform all service.
1.2 Installation Precautions
•
For best results, place the Tilt 'N Plug in a dry area away
from dust.
•
To prevent fire or shock, do not expose this unit to water
or moisture. Do not place the unit in direct sunlight, near
heaters or heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can harm
internal components.
•
Handle carefully; dropping or jarring can cause damage.
•
Never place fingers inside the opening on either side of
the unit; this could cause injury due to sharp edges.
•
Do not place heavy objects on top of the TNP. Do not
use excessive force to push down on the top of the unit.
•
Disconnect the power cord to turn off the power. This
supplies power to the socket on the pop-up panel. The
power outlet should be installed near the equipment and
be easily accessible.
•
We recommend using wall outlets with a Ground Fault
Circuit Interrupter (GFCI) for maximum protection.
•
Install cables according to the instructions found herein.
Do not force or pull any cables attached to the TNP.
1.3 Cleaning
•
Surfaces should be cleaned with a dry cloth. Never use
strong detergents or solvents such as alcohol or thinner.
Do not use a wet cloth or water to clean the unit.
2. Installation Procedures
Step 1 Cut an opening into the table’s surface. Refer to the Altinex website at www.altinex.com
for table cutout requirements.
NOTE The table can be 2.25 in (57 mm) or less in thickness. Always confirm dimensions
before cutting to insure that specifications have not changed.
Step 2. Insert the TNP327 into the table cutout.
Step 3. Place the support brackets under the table and place them between the support mount
grooves on the side of the unit. Attach the brackets to the groove at the desired height
and secure them to the bottom of the table using the knurled table securing screws
provided with the additional wing nuts for added tightening. See Diagram 3 for details.
Step 4. To lower the unit, push on the top cover until it locks into place.
Step 5. Secure all cables to the underside of the table using the cable clamps and screws
included with the TNP. Pass the power cord from the bottom of the housing and attach it
to the table separate from the signal cables. Leave enough slack in the service loop to
allow for easy opening and closing, but not too much as to cause excess drooping of the service loop.
Step 6. Connect the appropriate cables with the correct input connectors on the bottom of the unit.
Step 7. Once you have applied power and connected the proper cables on the bottom of the unit you may raise the unit. To raise the
unit into position, push down on the front of the top cover; the latching mechanism will then release, allowing the pneumatic
spring to raise it into position.
Note It may be necessary to adjust the service loop of the cables for optimal performance.
3.
Limited
Warranty/Return Policies
Please see the Altinex website at www.altinex.com for details on warranty and return policies.