TNP51
TNP51
TNP51
TNP510/512
0/512
0/512
0/512 Tilt ‘N Plug
Tilt ‘N Plug
Tilt ‘N Plug
Tilt ‘N Plug
®
User’s Guide
400-0521-001
1
Welcome!
We greatly appreciate your purchase of the Tilt ‘N Plug. We are sure you will
find it reliable and simple to use. Superior performance for the right price,
backed by solid technical and customer support is what ALTINEX has to
offer.
We are committed to providing our customers with
Signal Management Solutions
®
to the most demanding audiovisual
installations at very competitive pricing and we welcome you to join the
ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your TNP510/TNP512
Interconnect. Keep this manual handy for future reference. These safety
instructions are to ensure the long life of your TNP510/TNP512 and to
prevent fire and shock hazards. Please read them carefully and heed all
warnings.
1.1 General
•
Qualified ALTINEX service personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
•
For best results, place the TNP510/TNP512 Interconnect Box in a dry
area away from dust.
•
To prevent fire or shock, do not expose this unit to water or moisture.
Do not place it in direct sunlight, near heaters or heat-radiating
appliances, or near any liquid. Exposure to direct sunlight, smoke, or
steam can harm internal components.
•
Handle the unit carefully. Dropping or jarring can damage the bezel.
•
Never place fingers inside the opening on either side of the unit. This
action could cause injury due to sharp edges inside.
•
Do not place heavy objects on top of the TNP510/TNP512. Do not use
excessive force to push down on the top of the unit.
•
Disconnect the power cord to turn off the main power. This supplies
power to the power socket on the pop-up panel. The power outlet
should be installed near the equipment and should be easily accessible.
•
We recommend using wall outlets with a Ground Fault Circuit
Interrupter (GFCI) for maximum protection.
•
Install all cables according to the instructions found herein. Do not
force or pull out any cable or power cord attached to the unit.
1.3 Cleaning
•
Surfaces should be cleaned with a dry cloth. Never use strong
detergents or solvents such as alcohol or thinner. Do not use a wet cloth
or water to clean the unit.
1.4 FCC Notice
•
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
•
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions found herein, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his expense.
•
Any changes or modifications to the unit not expressly approved by
ALTINEX, Inc. could void the user’s authority to operate the
equipment.
2. Installation Procedures
Step 1.
Cut an opening into the table’s surface. Refer to the ALTINEX website at
www.altinex.com
for table cutout requirements.
Note: The table can be 2.50 in (64 mm) or less in thickness. Always confirm dimensions before cutting to insure that specifications have not changed.
Step 2.
Insert the TNP510/TNP512 into the table cutout.
Step 3.
Place the support brackets under the table and place them between the support mount grooves on the side of the unit. Attach the brackets to the
groove at the desired height and secure them to the bottom of the table using the thumb screws provided. See Diagram 5 for details.
Step 4.
To lower the unit, push on the top cover until it locks into place.
If Custom Plates are Installed
Step 5.
Secure all cables to the underside of the table using the cable clamps and screws included with the TNP510/TNP512. Pass the power cord from the
bottom of the housing and attach it to the table separate from the signal cables.
Leave enough slack in the service loop to allow for easy opening and closing, but not too much as to cause excess drooping of the service loop.
Step
6.
Connect the appropriate cables with the correct input connectors on the bottom of the unit.
Step 7.
Once you have applied power and connected the proper cables on the bottom of the unit you may raise the unit. To raise the unit into position, push
down on the front of the top cover; the latching mechanism will then release, allowing the pneumatic spring to raise it into position.
NOTE:
It may be necessary to adjust the service loop of the cables for optimal performance.
3. Limited Warranty/Return policies
Please see the ALTINEX website at
www.altinex.com
for details on warranty and return policies.
