Altigen Altiware HPBX 5.0A Скачать руководство пользователя | Manualshive

Страница: 340 / 490

background image

Setting Answering Options

10-48

AltiWare OE System Installation & Administration Manual

Handling Busy Calls

You have several options for handling calls while the extension is busy, and
again, the options vary depending on the extension type. If you do not
enable busy call handling, the caller simply hears a busy signal.

To enable the options, select the

Enable Busy Call Handling

check box,

then select from the following options:

•

Forward to Extension

—Select an extension number in the

drop-down list. See “A 10-Hop Limit to Call Forwarding for Direct
Calls” on page 10-46.

•

Forward to Voice Mail

•

Place Caller in Queue

—(

huntgroup/workgroup extensions only

)—

places the call to the group queue.

•

Forward to Auto Attendant

—use the drop-down list to select an

Auto Attendant to which to route the call. Auto Attendant settings are
established in

Auto Attendant Select…

on the

Management

menu.

•

To

Line Park

—if configured, select a

Line Park

group (configured in

“Line Park Configuration” on page 13-1) from the drop-down list.

Setting Call Waiting Options

Call waiting options are available only if the

Enable Busy Call Handling

check box has been selected, and this option is

not available to group

numbers

. However, the group pilot number does use the

Place Caller in

Queue

option discussed in the preceding subsection.

•

Enable Single Call Waiting

—sets up single call waiting. This feature

gives an alert tone (audio beep) to indicate that a call is waiting. This
feature must be enabled in order to conference incoming calls.

•

Enable Multiple Call Waiting

—enables a “personal queue” of

multiple calls waiting. You must also select the

Place Caller In

Queue

option under

Busy Call Handling

to enable this option. This

allows the user to transfer or park the current call before picking up the
next call in queue.

•

Enable Live Call Handling

—when enabled, allows a caller to hear a

ringback tone when the called party is in voice mail, paging, transfer,
or conference state.

Note:

The call will be shown as “ringing” in AltiConsole.

«
...
338
339
340
341
342
...
»

Содержание Altiware HPBX 5.0A











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Altiware HPBX 5.0A

Бренд: Canon Страницы: 2

Бренд: 3M Страницы: 3

Бренд: EAW Страницы: 36

Бренд: MACROMEDIA Страницы: 292

Бренд: MACROMEDIA Страницы: 26

Бренд: MACROMEDIA Страницы: 32

Бренд: Xerox Страницы: 28

Бренд: CSSN Страницы: 8

ALTIRIS 6 INVENTORY SOLUTION

Бренд: Symantec Страницы: 2

Unity Express 8.0 Voice-Mail System

Бренд: Cisco Страницы: 50

TELEPRESENCE MANAGEMENT SUITE PROVISIONING

Бренд: Cisco Страницы: 16

Unified MeetingPlace H.323/SIP

Бренд: Cisco Страницы: 54

PVDM2 24DM - Digital Modem Module

Бренд: Cisco Страницы: 48

TELEPRESENCE MANAGEMENT SUITE SECURE SERVER

Бренд: Cisco Страницы: 34

Бренд: Cisco Страницы: 8

Unified Videoconferencing Manager

Бренд: Cisco Страницы: 22

SMART BUSINESS COMMUNICATIONS SYSTEM

Бренд: Cisco Страницы: 27

MDS 9222i - Multiservice Modular Fabric Switch

Бренд: Cisco Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды