background image

 
 

TAEC Solar Box 

Owner’s Manual

 v2.2 

 

11 

 

PROBLEM 

POSSIBLE CAUSES 

REMARK 

No power on the 
control panel 

Lack of power 

Check that there is power at the Solar Box 
Check the corresponding circuit breaker is 
turned on  

Disconnected or 
damaged wiring 

Check the electric or electronic circuit 
Check the electrical protection (RES fuse), 
located at the back of controller (display) 
Check the cabling 
Check that the cable to the control panel 
is connected 

Low water 
temperature 

No power to control 
panel 

See above 

Equipment turned off 

Press ON/OFF button 

Compressor turned off 

Turn on the compressor using the 

“COMP” button

 

No power to compressor 
or electrical element 

Check for errors on the electronic panel, 
fuses, and relays 

Temperature set point 
not set correctly 

Adjust the set point temperature 

Temperature probe not 
correctly located 

Check location of probe 

Hot water returning to 
the cold water circuit 
(damaged or incorrectly 
installed safety valve) 

Close the cold water inflow valve to turn 
off the safety group.  Open a hot tap.  
Wait for 10 minutes and if hot water is 
available replace the defective pipe 
and/or correct the position of the safety 
group. 
Clean the safety group filter 

Disinfect mode 
constantly on 

Thermostat of hot water 
electrical element set 
too low 

Set thermostat on hot water cylinder 
element to 70°C (greater than disinfect 
temperature) 

Excessively hot 
water 

Faulty temperature 
gauge 

Check for errors on the electronic panel 

Faulty Control panel 

Problem with control board so 
compressor or element constantly on 

Low hot water 
flow (HP alarm) 

No water in hot water 
cylinder or Solar Box 

Check cylinder and pipework 

Loss or blockage of the 
hydraulic circuit 

Check the state of the hydraulic circuit 
Check strainer 

Pump air locked 

Bleed system using bleed valve to remove 
air from pump and heat exchanger 

Water leaking 
from the safety 
valve located 
over drain. 

Absence of or 
incorrectly sized 
expansion tank (if the 
leak is intermittent) 
 

Installation and/or correct sizing of 
expansion tank 
Check the piping for damage 

3.

 

Fault finding / Problem solving 

Содержание Energie Solar Box
















Отзывы: