manualshive.com logo in svg

Altera Stratix V Hard IP, Руководство пользователя, Страница: 213 / 232

Поделиться
Скачать
Altera Stratix V Hard IP Скачать руководство пользователя страница 213

Chapter 14: Hard IP Reconfiguration and Transceiver Reconfiguration

14–9

Transceiver PHY IP Reconfiguration

June 2012

Altera Corporation

Stratix V Hard IP for PCI Express

User Guide

Transceiver PHY IP Reconfiguration

As silicon progresses towards smaller process nodes, circuit performance is affected 
by variations due to process, voltage, and temperature (PVT). In some cases, you must 
compensate for these variations by including the Transceiver Reconfiguration 
Controller IP Core in your design and selecting the appropriate reconfiguration 
functions. 

Table 14–1

 lists transceiver reconfiguration requirements.

1

You must disable offset cancellation if your design includes CvP. 

Connecting the Transceiver Reconfiguration Controller IP Core

Figure 14–1

 shows the connections between the Transceiver Reconfiguration 

Controller instance and the PHY IP Core for PCI Express instance for a ×4 variant. 

Table 14–1. Transceiver Reconfiguration Requirements for Stratix V Devices

Lane Rate

Required Reconfiguration Functions

Gen1 ES 

None, Transceiver Reconfiguration Controller not required

Gen2 ES

Offset cancellation

Gen3 ES

Offset cancellation and adaptive dispersion compensation engine (ADCE)

Gen1 production devices None, Transceiver Reconfiguration Controller not required

Gen2 production devices Pending characterization

Gen3 production devices Pending characterization

Figure 14–1. Altera Transceiver Reconfiguration Controller Connectivity 

 Avalon-MM 

Slave Interface

PHY IP Co

r

e fo

r

 PCI Exp

r

ess

Lane 2

Lane 3

Lane 1

Lane 0

TX PLL

T

r

ansceive

r

 Bank

to and from

Embedded

Controller

100-125 MHz

T

r

ansceive

r

 Reconfigu

r

a

t

ion Con

tr

olle

r

(Unused)

mgmt_clk_clk
mgmt_rst_reset
reconfig_mgmt_address[6:0]
reconfig_mgmt_writedata[31:0]
reconfig_mgmt_readdata[31:0]
reconfig_mgmt_write
reconfig_mgmt_read
reconfig_mgmt_waitrequest

reconfig_to_xcvr

reconfig_from_xcvr

reconfig_busy

S

tr

a

t

ix V Ha

r

d IP fo

r

 PCI Exp

r

ess Va

r

ian

t

Ha

r

d IP fo

r

 PCI Exp

r

ess

T

r

ans-

ac

t

ion

Da

t

a

Link

PHY

Содержание Stratix V Hard IP









































































































































































































































Отзывы:

Нет отзывов