background image

Enpirion

®

 Power Evaluation Board User Guide 

EN6360QI PowerSoC 

Test Recommendations 

Recommendations 

To guarantee measurement accuracy, the following precautions should be 
observed: 
 

1.  Make  all input and output voltage measurements at the board using the 

surface-mount test points  provided. This will eliminate voltage  drop 
across the line and load cables that can produce false readings. 

2.  Measure  input and output current with series ammeters or accurate 

shunt resistors. This is especially  important  when measuring efficiency. 

3.  Use a low-loop-inductance  probe tip shown below to measure V

OUT

 

and switching signals to avoid noise coupling into the probe ground 
lead.  Output ripple and load transient deviations  are conveniently 
measured at TP19. For more accurate ripple  measurement, please 
refer to Enpirion App Note regarding this subject 
(

www.altera.com/enpirion

). 

 

 

4.  The board includes a pull-up for the POK signal and ready to monitor 

the power OK status. 

5.  A soft-start capacitor is populated  on the board to provide a reasonable 

soft-start time. It  can be changed  as needed. 

6.  The over-current  protection  circuit typically  limits the maximum load 

current to approximately  14.5A.   

 

Input and Output Capacitors 

 

Please refer to the BOM section for the value of input caps and output caps used 
on this evaluation  board,  which is the result of combination  for better 
performance and  smaller footprints. 
 
 

NOTE:

 Capacitors must be X5R or X7R dielectric formulations  to ensure 

adequate  capacitance over operating  voltage  and temperature ranges. 
 
 
 
 
 
 

Page 7 of 9 

www.altera.com/enpirion

 

Содержание Enpirion EN6360QI










Отзывы: