Altera Cyclone V страница 989 Скачать руководство пользователя | Manualshive

Страница: 989 / 1077

background image

23

Timer Introduction

2013.12.30

cv_54023

Send Feedback

The hard processor system (HPS) provides four, 32-bit, general-purpose timers connected to the level 4 (L4)
peripheral bus.
The timers optionally generate an interrupt when the 32-bit binary count-down timer reaches zero. The
timers are instances of the Synopsys

®

DesignWare

®

APB Timers (DW_apb_timers) peripheral.

Portions

©

2013 Synopsys, Inc. Used with permission. All rights reserved. Synopsys & DesignWare

are registered trademarks of Synopsys, Inc. All documentation is provided "as is" and without any

Note:

warranty. Synopsys expressly disclaims any and all warranties, express, implied, or otherwise, including
the implied warranties of merchantability, fitness for a particular purpose, and non-infringement,
and any warranties arising out of a course of dealing or usage of trade.

†Paragraphs marked with the dagger (†) symbol are Synopsys Proprietary. Used with permission.

Related Information

Cortex-A9 MPCore

on page 6-4

The MPU subsystem provides additional timers. For more information about the timers in the MPU, refer
to the

Cortex-A9 Microprocessor Unit Subsystem

chapter.

Features of the Timer

• Supports interrupt generation
• Supports free-running mode
• Supports user-defined count mode

Timer Block Diagram and System Integration

Each timer includes a slave interface for control and status register (CSR) access, a register block, and a
programmable 32-bit down counter that generates interrupts on reaching zero. The timer operates on a
single clock domain driven by the clock manager.

9001:2008
Registered

©

2013 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words

and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other
words and logos identified as trademarks or service marks are the property of their respective holders as described at

www.altera.com/common/legal.html

. Altera warrants performance of its semiconductor products to current specifications in accordance with

Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes
no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly
agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published
information and before placing orders for products or services.

www.altera.com

101 Innovation Drive, San Jose, CA 95134

«
...
987
988
989
990
991
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

Univerge SV8100

Бренд: NEC Страницы: 44

InterReach Fusion ADCP-77-044

Бренд: TE Connectivity Страницы: 236

EXPANSION CARD X-DANTE

Бренд: Behringer Страницы: 65

Бренд: Rolls Страницы: 2

Бренд: Barco Страницы: 30

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: ZyXEL Communications Страницы: 3

Power System S914

Бренд: IBM Страницы: 48

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Sony Ericsson Страницы: 2

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: Cooler Master Страницы: 4

Бренд: ELSA Страницы: 60

Бренд: Helmholz Страницы: 14

CP 040 RS422/485

Бренд: YASKAWA Страницы: 87

Бренд: ANTAIRA Страницы: 6

Бренд: Cabletron Systems Страницы: 56

EK-FC 780 GTX Lightning

Бренд: ekwb Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды