manualshive.com logo in svg

Altera Cyclone V, Руководство по эксплуатации устройства

Поделиться
Скачать
Altera Cyclone V Скачать руководство пользователя страница 550

Cortex-A9 MPU Subsystem Components

The Altera Cortex-A9 MPU subsystem consists of the following hardware blocks:

• ARM Cortex-A9 MPCore
• ARM L2C-310 L2 cache controller
• ACP ID mapper
• Debugging and trace features

Cortex-A9 MPCore

The MPU subsystem includes a stand-alone, full-featured ARM Cortex-A9 MPCore single- or dual-core
32-bit application processor. The processor, like other HPS masters, can access IP in the FPGA fabric through
the HPS-to-FPGA bridges.

Functional Description

The ARM Cortex-A9 MPCore contains the following blocks:

• One or two Cortex-A9 Revision r3p0 processors operating in SMP or AMP mode
• Snoop control unit (SCU)
• Private interval timer for each processor core
• Private watchdog timer for each processor core
• Global timer
• Interrupt controller

Each transaction originating from the Altera Cortex-A9 MPU subsystem can be flagged as secure or nonsecure.

Implementation Details

Table 6-1: Cortex-A9 MPCore Processor Configuration

This table shows the parameter settings for the Altera Cortex-A9 MPCore.

Options

Feature

1 or 2

Cortex-A9 processors

32 KB

Instruction cache size per Cortex-A9 processor

32 KB

Data cache size per Cortex-A9 processor

128 entries

TLB size per Cortex-A9 processor

Included

Media Processing Engine with NEON

™

technology

per Cortex-A9 processor

(4)

Included

Preload Engine per Cortex-A9 processor

16

Number of entries in the Preload Engine FIFO per
Cortex-A9 processor

(4)

Includes support for floating-point operations.

Cortex-A9 Microprocessor Unit Subsystem

Altera Corporation

Send Feedback

cv_54006

Cortex-A9 MPU Subsystem Components

6-4

2013.12.30

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды