Altera Cyclone IV Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 490

Altera Cyclone IV Скачать руководство пользователя страница 182

8–18

Chapter 8: Configuration and Remote System Upgrades in Cyclone IV Devices

Configuration

Cyclone IV Device Handbook,

May 2013

Altera Corporation

Altera recommends putting a buffer before the

DATA

and

DCLK

output from the master

device to avoid signal strength and signal integrity issues. The buffer must not
significantly change the

DATA

-to-

DCLK

relationships or delay them with respect to other

AS signals (

ASDI

and

nCS

). Also, the buffer must only drive the slave devices to ensure

that the timing between the master device and the serial configuration device is
unaffected.

This configuration method supports both compressed and uncompressed

.sof

.

Therefore, if the configuration bitstream size exceeds the capacity of a serial
configuration device, you can enable the compression feature in the

.sof

or you can

select a larger serial configuration device.

Guidelines for Connecting a Serial Configuration Device to Cyclone IV
Devices for an AS Interface

For single- and multi-device AS configurations, the board trace length and loading
between the supported serial configuration device and Cyclone IV device must follow
the recommendations listed in

Estimating AS Configuration Time

AS configuration time is dominated by the time it takes to transfer data from the serial
configuration device to the Cyclone IV device. This serial interface is clocked by the
Cyclone IV device

DCLK

output (generated from a 40-MHz internal oscillator for

Cyclone IV E devices, a 20- or 40-MHz internal oscillator, or an external

CLKUSR

of up

to 40 MHz for Cyclone IV GX devices).

and

show the configuration time calculations.

Table 8–7. Maximum Trace Length and Loading for AS Configuration

Cyclone IV

Device AS Pins

Maximum Board Trace Length from a

Cyclone IV Device to a Serial Configuration

Device (Inches)

Maximum Board Load (pF)

Cyclone IV E

Cyclone IV GX

DCLK

10

6

15

DATA[0]

10

6

30

nCSO

10

6

30

ASDO

10

6

30

Note to

Table 8–7

(1) For multi-devices AS configuration using Cyclone IV E with 1,0 V core voltage, the maximum board trace-length

from the serial configuration device to the junction-split on both

DCLK

and

Data0

line is 3.5 inches.

Equation 8–2.

Equation 8–3.

Size

maximum DCLK period

1 bit

----------------------------------------------------------------











estimated maximum configuration ti

=

9,600,000 bits

50 ns

1 bit

-------------











480 ms

=

«
...
180
181
182
183
184
...
»

Содержание Cyclone IV











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды