ALTAI MIS200P Скачать руководство пользователя страница 27

Страница: 27 / 27

Quick Setup Guide

Warning

MIS200P may require professional installation depending on the deployment scenario.

The metal chassis of the equipment may be hot. Pay special attention or use special protection before

handling this equipment.

Disclaimer

All specifications are subject to change without prior notice. Altai Technologies assumes no responsibilities

for any inaccuracies in this document or for any obligation to update information in this document. This

document is provided for information purposes only. Altai Technologies reserves the right to change, modify,

transfer, or otherwise revise this publication without notice.

Altai Technologies Limited

Unit 209, 2/F, Lakeside 2,
10 Science Park West Avenue,
Hong Kong Science Park,
Shatin, New Territories,
Hong Kong

Telephone: +852 3758 6000
Fax: +852 2607 4021
Web:

www.altaitechnologies.com

Customer Support Centre:

Email:

[email protected]

Содержание MIS200P



























Результаты поиска

Содержание MIS200P

Отзывы:

Бренды по названию

Популярные бренды

ALTAI MIS200P, Быстрая настройка

Результаты поиска

Содержание MIS200P

Отзывы:

Бренды по названию

Популярные бренды