8. ADJUST MOTOR SPEED
6. ROLLER MODE AND SHEER MODE
7. ADD OR REMOVE ADDITIONAL WALL SWITCH
5. FAVORITE POSITION
2. CHANGE MOTOR DIRECTION (IF NECESSARY)
3. SETTING THE UPPER AND LOWER LIMITS
4. ADJUST LIMITS
1. PAIR / UNPAIR WALL SWITCH
Jog x1
Jog x1
Jog x2
Beep x1
Beep x1
Beep x3
CHANNEL OPTIONS
*Honeycomb /Cellular and
Horizontal Blind Motors
DO NOT BEEP.
GETTING STARTED
It is important to confim that the motor is awake and ready to receive programming. To do
this, press “P1” button on the motor less than 1 sec, to activate the motor from Sleep Mode.
a. Press
“P1” button (about 2 sec)
on the motor head until motor jog
x1 and beep x1.
b. In the next 10 secs, press and
hold
“Stop” button on the wall
switch until motor jog x2 and
beep x3.
ADJUST THE UPPER LIMIT
a. Press and hold (about 5 sec)
“Up”
and “Stop” buttons simultaneously
until motor jog x1 and beep x1.
b. Use
“Up” button to raise the
shade to the desired highest
position, and use
“Up” or “Down”
button to do the final adjustment if
necessary.
c. Press and hold (about 5 sec)
“Up”
and “Stop” buttons simultaneously
until motor jog x2 and beep x3.
ROLLER SHADE MODE -Default
mode, allows for continuous
raising/lowering of shade after
a short press.
a. Press and hold (about 5 sec)
“Up” and “Down” buttons
simultaneously until motor jog x1.
b. Press and hold (about 2 sec)
“Stop” button until motor jog x2
and beep x3.
USING CURRENT WALL SWITCH
a. On the
current wall switch,
press and hold (about 2 sec) one
“P2” button until motor jog x1 and
beep x1.
b. Once more, on the
current wall
switch, press and hold (about 2 sec)
one
“P2” button until motor jog x1
and beep x1.
c. On the
New wall switch, press
and hold (about 2 sec) one
“P2”
button until motor jog x2 and
beep x3.
INCREASE MOTOR SPEED
a. Press one
“P2” button until motor
jog x1 and beep x1.
b. Press
“Up” button until motor jog
x1 and beep x1.
c. Once more, press
“Up” button
until motor jog x2 and beep x1.
SHEER SHADE MODE -
Allows for
slight adjustment after a short
press and raising/ lowering of
shade after a longer press.
a. Press and hold (about 5 sec)
“Up” and “Down” buttons
simultaneously until motor jog x1.
b. Press and hold (about 2 sec)
“Stop” button until motor jog x1
and beep x1.
DECREASE MOTOR SPEED
a. Press one
“P2” button until motor
jog x1 and beep x1.
b. Press
“Down” button until motor
jog x1 and beep x1.
c. Once more, press
“Down” button
until motor jog x2 and beep x1.
HIDE UNUSED CHANNELS
SET FAVORITE POSITION
a. Use
“Up” or “Down” button to
move the shade to desired Favorite
position.
b. Press and hold (about 2 sec)
one
“P2” button on the back of
wall switch until motor jog x1 and
beep x1.
c. Press and hold (about 2 sec)
“Stop” button until motor jog x1
and beep x1.
d. Once more, press and hold
(about 2 sec)
“Stop” button until
motor jog x2 and beep x3.
DELETE FAVORITE POSITION
a. Press and hold (about 2 sec) one
“P2” button until motor jog and
beep x1.
b. Press and hold (about 2 sec)
“Stop” button until motor jog and
beep x1.
c. Once more, press and hold
(about 2 sec)
“Stop” button until
motor jog x1 and long beep x1.
ADJUST THE LOWER LIMIT
a. Press and hold (about 5 sec)
“Down” and “Stop” buttons
simultaneously until motor jog x1
and beep x1.
b. Use
“Down” button to lower the
shade to the desired lowest position,
and use
“Up” or “Down” button to
do the final adjustment if necessary.
c. Press and hold (about 5 sec)
“Down” and “Stop” buttons
simultaneously until motor jogs x2
and beeps x3.
SEND SHADE TO FAVORITE
POSITION
Press and hold (about 2 sec)
“Stop” button, motor will move to
Favorite position.
Press
“Up” or “Down” button to
check if the shade moves in the
desired direction.
If you need to reverse the direction,
press and hold (about 2 sec)
“Up”
and “Down” buttons simultaneously
until motor jog x1 and beep x1.
SET UPPER LIMIT
a. Press
“Up” button to raise the
shade, then press
“Stop” button
when it is in the desired upper limit.
b. Press and hold (about 5 sec)
“Up”
and “Stop” buttons simultaneously
until motor jog x2 and beep x3.
*The operation is only valid when there are no limits. If the motor has already set the
upper and lower limit, then you can only switch direction by pressing
“P1” button
(about 10 sec) on the motor head until motor jog x3 and beep x3.
* Repeat the same procedure to
unpair wall switch.
*If you exit the limit setting status before you finish the
limit settings, the motor will take the previous existing
limits.
*If the motor has no response, it
already has a Maximum or Minimum
speed.
SET LOWER LIMIT
a. Press
“Down” button to lower
the shade, then press
“Stop” button
when it is in the desired lower limit.
b. Press and hold (about 5 sec)
“Down” and “Stop” buttons
simultaneously until motor jog x2
and beep x3
.
Action on
Motor
Action on
Wall Switch
+
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor
Response
Motor
Response
Motor
Response
Motor
Response
Motor
Response
Up
Down
Stop
P1
a.
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
b.
a.
a.
c.
b.
b.
b.
b.
c.
c.
b.
c.
c.
c.
c.
c.
d.
Jog x2
Jog x2
Beep
x3
Beep
x3
+
+
Up
Up
Down
Stop
Stop
Down
a.
a.
b.
a.
b.
b.
Jog x1
Jog x2
Beep
x1
Beep x3
+
+
Up
Up
Up
Stop
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor
Response
Motor
Response
Motor
Response
Motor
Response
Stop
Jog x1
Beep
x1
+
Down
Stop
Down
Jog x2
Beep x3
+
Down
Stop
Jog x1
Jog x2
Beep x3
+
Up
Down
Stop
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
Jog x1
Jog x1
Beep x1
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
+
+
or
Up
Lower
Channel
Lower
Channel
Down
Higher
Channel
Higher
Channel
Stop
Jog x1
Jog x2
Jog x1
Beep x1
Beep x3
Beep x1
Current Wall Switch
New Wall Switch
Current Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor
Response
Motor
Response
Jog x1
Jog x1
Jog x1
Jog x2
Jog x1
Jog x2
Beep x1
Beep x1
Beep x1
Beep x1
Beep x1
Beep x1
Up
Higher
Channel
Lower
Channel
Up
Down
Down
Stop
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor
Response
Wall Switch
Response
Motor
Response
Motor
Response
Wall Switch
Response
Wall Switch
Response
Motor
Response
Wall Switch
Response
P1
P1
NEW WALL SWITCH CONTROL
Follow instructions under the section
1. Pair / Unpair Wall Switch
*Repeat the same procedure to
remove additional wall switch.
Factory Mode Complete
User Mode Begins
P2 Button
P2 Button
P2 Button
P2 Button
P2 Button
P2 Button
P2 Button
SELECT A CHANNEL
a. Press “-” button on the wall
switch to select a lower channel.
b. Press “+” button on the wall
switch to select a higher channel.
a. Press and Hold (about 3 sec)
“-” and “+” buttons simultane-
ously until wall switch displays “C”
(channel).
b. Press
“-” or “+” button to select
required quantity of channel
(between 1 to 15).
c. Press
“Stop” button to confirm
selection (the example shows a
5-channel selection). The LED will
display “O” (OK) once to confirm
selection.
Jog x1
Jog x1
Jog x2
Beep x1
Beep x1
Beep x3
Jog x1
Jog x1
Jog x1
Beep x1
Beep x1
Beep x1
or
or
or
Up
Down
Stop
Stop
Stop
Stop
Stop
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor
Response
Shade
Response
Motor
Response
Motor
Response
Motor
Response
