22
-EN
If an Alpine Ai-NET Interrupt Box (NVE-K200) is connected to the
unit, an Auxiliary Source will be allowed to interrupt the current audio
source. For example, you can listen to the voice guidance of your
navigation system when it occurs even while you are playing a song
stored in the USB memory. The song will be automatically muted
during voice guidance. For further details, please refer to the manual for
NVE-K200.
Setting item: IN Int. Mute
Setting contents: OFF / ON
•
The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.
The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN Int. Icon
Setting contents: INT / TEL
For optional remote control operation, the remote sensor of the external
device (monitor, etc.) can be switched, as you prefer.
Setting item: Remote Sensor
Setting contents: FRONT / REAR
•
If a touch screen monitor (connected to the Rear Monitor output
using the Monitor control lead) is touched, the command is executed
regardless of the remote control sensor setting. Note, however, that
the remote control sensor that has been set takes priority if it has
been 5 seconds since last touching the panel.
•
When an optional DVD changer is connected, and the remote control
sensor is set to REAR, some soft button operations (
[
]
STOP, etc.)
cannot be performed. In this case, set the remote control sensor to
FRONT.
With a rear camera connected, rear view video is output to the monitor.
Setting item: Camera IN
Setting contents: OFF / DIRECT / RCA
•
By shifting to reverse (R), the rear pictures are output.
This function is effective when the reverse wire is properly connected.
After setting to RCA or DIRECT in “Setting the Rear Camera Input”,
this setting can be carried out.
Setting item: Camera Signal
Setting contents: NTSC/PAL / AUTO
•
When set to AUTO, unstable display may occur while playing back
certain black and white video signal. In this case, select NTSC or
PAL mode manually.
When you connect an optional navigation device, set it to ON.
Setting item: NAV. IN
Setting contents: OFF / ON
With an Alpine navigation system connected to the iXA-W404R, the
voice guidance of the navigation system will be mixed with the radio or
iPhone/iPod play.
Setting item: NAV. Mix
Setting contents: OFF / ON
See “Adjusting NAV. Mix Level” under “Adjusting the Audio” on
page 14 to set the navigation interruption volume level.
•
The volume level for voice prompts during navigation guidance is set
by adjusting the volume while the prompts are announced. When the
announcement finishes, the normal audio volume and the previous
audio screen are restored. The voice prompt volume is always at or
below the current listening volume. If a navigation announcement
cuts in while adjusting the audio level, it always resets to the current
level regardless of the audio level setting.
•
This setting is effective when NAV. IN of SYSTEM list screen is ON.
Setting the External Device Interrupt Mode
OFF:
The volume level can be adjusted in Interrupt mode.
ON:
Sound will not be output. The icon that is set in “Setting
the Interrupt Icon Display” is displayed.
Setting the Interrupt Icon Display
INT:
The INT icon appears on the display.
TEL:
When the external device (telephone) sends the interrupt
signal, the telephone icon appears on the display.
Switching the function of the remote
sensor
FRONT:
The remote sensor of this unit is effective.
REAR:
The remote sensor of the external monitor
connected to AUX OUT of this unit becomes
effective. The remote control operates the
source connected to the AUX OUT terminals.
Setting the Rear Camera Input
OFF:
The Camera mode is not displayed in the mode
switching screen.
DIRECT:
Use when the optional rearview camera
HCE-C107D is connected.
RCA:
Use when connect an optional rearview camera
with RCA output connector.
Setting the Rear Camera Signal Input
NTSC/PAL:
Choose the video input signal type manually.
AUTO:
The suitable video input signal type will be
automatically chosen between NTSC and PAL.
Setting the Navigation Mode
OFF:
Navigation mode is not displayed. The settings related to
the navigation can not be changed from this unit.
ON:
Navigation mode is displayed.
Setting the Navigation Interruption
OFF:
The navigation interruption mode is turned off.
ON:
The navigation interruption mode is on.
Содержание iXA-W404R
Страница 2: ......
Страница 59: ...57 EN List of World Clock For details see page 15 Information ...
