46
-EN
01GB06IVAW200.fm
ALPINE IVA-W200 68-04123Z67-A (EN)
The test tones help to make the volume adjustments of the different
speakers. When levels are equal, a strong sense of presence can be heard
from the different speakers at the listening position.
•
Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the decode mode is switched.
1 Touch
[ON]
of OUTPUT LEVEL.
Test tone output is repeated for each of the different
speaker channels. They will be repeated in the order
shown below.
If no operation is performed for 2 seconds, the channel
switches to the next channel.
2 While the test tone is being produced from the speakers,
touch
[
]
or
[
]
of OUTPUT LEVEL balance the output
from all the speakers.
•
If a speaker is set to off mode, that speaker’s level adjustment cannot
be made.
Refer to “Speaker Setup” (page 44).
Adjusting the DVD Level
The volume (signal level) for Dolby Digital, Dolby PL II, DTS and
PCM modes can be set.
•
Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
1
Check that Defeat mode is off.
2
Touch
[SETUP]
on the main source screen.
The SETUP selection screen appears.
3
Touch
[i-Personalize]
.
The i-Personalize screen will appear.
4
Touch
[
]
of A.PROCESSOR.
The A.PROC list screen appears.
5
Touch
[
]
of DVD LEVEL.
The DVD LEVEL list screen appears.
6
Adjust the level by touching
[
]
or
[
]
of the
desired adjusting mode.
The level can be adjusted in the range of –5 to +5.
Storing Settings in the Memory
Adjustment or setting contents can be stored.
Contents that can be stored vary depends on the audio processor used.
1
Check that Defeat mode is off (page 24).
2
Touch
[MEMORY]
on the A.PROC list display.
3
Within 5 seconds, touch any one of the preset
buttons
[P.SET 1]
through
[P.SET 6]
on the
A.PROC list screen.
The setting contents are stored.
•
The stored contents will not be deleted even when the battery power
cord is detached.
Getting out the Preset Memory
1
Check that Defeat mode is off.
2
Touch any one of the preset buttons
[P.SET 1]
through
[P.SET 6]
on the A.PROC list display to
select the preset memory.
•
It takes a few moments to get out the preset memory.
Using the Pro Logic II Mode
Pro Logic processing can be conducted on the music signals recorded
on two channels to achieve Dolby Pro Logic II surround sound. For
two-channel Dolby Digital and DTS signals, there is also a “REAR
FILL” function for outputting the signals of the front channel to the rear
channel.
1
Check that Defeat mode is off.
2
Touch
[SETUP]
on the main source screen.
The SETUP selection screen appears.
3
Touch
[i-Personalize]
.
The i-Personalize screen will appear.
4
Touch
[
]
of A.PROCESSOR.
The A.PROC list screen appears.
5
Touch
[
]
of DOLBY PLII/REAR FILL.
The DOLBY PLII/REAR adjusting screen appears.
6
Touch
[
]
or
[
]
of DOLBY PLII/REAR to select the
desired mode.
Adjusting the speaker levels
(OUTPUT LEVEL)
Left
Center
Right
Right
Surround
Left Surround
Left
•
The adjustment range for the different speakers is
–10 dB - +10 dB.
•
Adjust based on the front speakers.
PL II MOVIE:
Suits the stereo TV shows and all programs
encoded in Dolby Surround. It improves the
sound field directivity to near that of discrete
5.1-channel sound.
PL II MUSIC:
Can be used for all stereo music recordings, and
provides a wide, deep sound field.
OFF:
Turns DOLBY PL II function to OFF.
01GB00IVAW200.book Page 46 Tuesday, December 20, 2005 11:41 AM
Содержание IVA W200 - DVD Player With LCD Monitor
Страница 77: ...LIMITED WARRANTY ...
