manualshive.com logo in svg

Alpine CDE-9850Ri, Руководство пользователя

Поделиться
Скачать
Alpine CDE-9850Ri Скачать руководство пользователя страница 16

15

-EN

01GB05CDA-9854R.fm

ALPINE CDE-9850Ri 68-04123Z56-A (EN)

Adjusting Bass/Treble/Balance (Between 
Left and Right)/Fader (Between Front 
and Rear)/Defeat

1

Press 

MODE

 repeatedly to choose the desired 

mode.

Each press changes the mode as follows:

BASS  

TREBLE  

SUBW

*

  

BALANCE  

FADER  

DEFEAT 

 VOLUME 

 BASS

Bass Level: –7 ~ +10
Treble Level: –7 ~ +7
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35

•

If 

MODE

 is not pressed within 5 seconds after selecting the BASS, 

TREBLE, BALANCE, FADER, DEFEAT or SUBW mode, the unit 
automatically returns to normal mode.

* When the subwoofer mode is set to OFF, its level cannot be adjusted.

2

Turn the 

Rotary encoder

 until the desired sound is 

obtained in each mode.

By setting Defeat ON, previously adjusted settings of BASS 
and TREBLE will return to the factory defaults.

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal 
preference.

1

Press 

MENU

 to select the BASS ENGINE mode, then 

press 

MODE

.

BASS ENGINE 

 SETUP 

 RETURN (OFF) 

 BASS ENGINE

2

Press 

 or 

 to select the BASS (bass Centre 

frequency) control mode.

BASS  

TREBLE

3

-1 Press 

SOURCE/POWER

 to select the desired bass 

centre frequency.

80Hz  

100Hz  

120Hz  

60Hz  

80Hz

Emphasize the displayed bass frequency ranges.

3

-2 Press 

BAND

 to select the desired bass bandwidth.

Change the boosted bass bandwidth to wide or narrow. A 
wide setting will boost a wide range of frequencies above 
and below the centre frequency. A narrower setting will 
boost only frequencies near the centre frequency.

3

-3

*

1

Turn the 

Rotary encoder

 to select the desired 

bass level (–7~+10).

You can emphasize or weaken the bass level.

4

Press 

MENU

 to select RETURN.

After 2 seconds, the unit returns to normal mode.
Pressing and holding 

MENU

 for at least 2 seconds will 

return to normal mode.

•

If no operation is performed within 60 seconds, the bass control 
setting will be turned off automatically.

•

The bass level settings will be individually memorized for each 
source (FM, MW (LW), CD, etc.) until the setting is changed. The 
bass frequency and bass band width settings adjusted for one source 
are effective for all other sources (FM, MW (LW), CD etc.).

•

Depending on the connected devices, some functions and display 
indications do not work. However, Bass Level is still adjustable if an 
audio processor with the Bass function is connected.

•

This function is inoperable when DEFEAT is set to ON.

•

If you press 

 or 

 in the bass control mode, the unit 

changes to the treble control mode.

*

1

The adjustment can also be made by pressing 

MODE

. Refer to 

“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader 
(Between Front and Rear)/Defeat” (page 15).

Bass level indicator’s display

Sound Setting

BAND

Rotary encoder

MODE

SOURCE/POWER

MENU

Setting the Bass Centre Frequency

Setting the Bass Bandwidth

Setting the Bass Level

Bass level is usually displayed.

01GB00CDA-9854R.book  Page 15  Wednesday, October 19, 2005  8:21 AM

Содержание CDE-9850Ri































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды