29
-EN
To prevent noise/interference in the audio system.
•
Locate the unit and route the leads at least 10 cm away from the car harness.
•
Keep the battery power leads as far away from other leads as possible.
•
Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
•
If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
•
Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
1
Vehicle Display Interface Connector
Outputs Vehicle Display Interface control signals. Connect
this to the optional Vehicle Display Interface box.
For details about connections, consult your nearest ALPINE
dealer.
2
Antenna Receptacle
3
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
4
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
5
Dimmer Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
6
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
7
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
8
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
9
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
!
ISO Power Supply Connector
"
ISO Connector (Speaker Output)
#
Left Rear (+) Speaker Output Lead (Green)
$
Left Rear (–) Speaker Output Lead (Green/Black)
%
Left Front (+) Speaker Output Lead (White)
&
Left Front (–) Speaker Output Lead (White/Black)
(
Right Front (–) Speaker Output Lead (Grey/Black)
)
Right Front (+) Speaker Output Lead (Grey)
~
Right Rear (–) Speaker Output Lead (Violet/Black)
+
Right Rear (+) Speaker Output Lead (Violet)
,
Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, iPod adapter,*
2
etc.)
equipped with Ai-NET.
*
2
If you connect to the iPod, you need the optional adapter
(KCA-420i). For details on connection, refer to the Owner's
Manual of the KCA-420i.
-
Steering Remote Control Interface Connector
To steering remote control interface box.
.
Fuse Holder (10A)
/
Rear Output RCA Connectors
RED is right and WHITE is left.
:
Front Output RCA Connectors
RED is right and WHITE is left.
;
Subwoofer Output RCA Connectors
RED is right and WHITE is left.
<
System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
• Be sure to turn the power off to the unit before changing the switch
position.
=
Power Supply Connector
>
Ai-NET Cable (Included with CD Changer)
?
RCA Extension Cable (Sold Separately)
@
ISO/JASO Antenna Adaptor (Sold Separately)
An ISO/
JASO
antenna adapter may be required, depending
on the vehicle.
Содержание CDA-9851R
Страница 34: ......
