Alpine CDA-117Ri, Руководство пользователя

Страница: 20 / 50

18
-EN
3
Turn the Rotary encoder to adjust the level.
Adjustable level: −6 to +6 dB
4
Press SOURCE

to set the bandwidth (Q).
Adjustable bandwidth: 1, 2, 3, 4
5
To adjust another band, repeat steps 1 to 4 and adjust all
bands.
Note
• While adjusting the Parametric EQ, you should consider the frequency
response of the connected speakers.
Adjusting the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ Mode to Graphic EQ. For details, refer to “Setting EQ mode”
on page 17.
1
After selecting Graphic EQ from the Sound Field mode,
press
BAND  TA to select the band to be adjusted.
Band 1

Band 2

Band 3

Band 4

Band 5

Band 6

Band 7

Band 1
2
Turn the Rotary encoder to adjust the level.
Adjustable output level: −6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and then
adjust all bands.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” on page 34.
1
After selecting T.Correction from the Sound Field mode,
press
BAND  TA to select a speaker to be adjusted.
F-L
*1

F-R
*2

R-L
*3

R-R
*4

SW-L

SW-R

F-L
*1
Front-L (Initial setting)
*2
Front -R
*3
Rear-L
*4
Rear-R
2
Turn the Rotary encoder to adjust the distance correction
value (0.0 to 336.6cm).
L = (distance to farthest speaker) - (distance to other speakers)
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the listening
position at the same time as the sound of other speakers.
Storing the Sound Field Adjustment Settings
The Sound Field Settings containing Parametric EQ/Graphic EQ and
T.Correction settings can be stored in the preset memory.
1
When the settings of Sound Field have been completed,
select any one of the
preset buttons (1 through 6) in any
item of the Sound Field mode (e.g. Parametric EQ), press
and hold the desired preset buttons for at least 2 seconds.
2
Turn the Rotary encoder to select PROTECT YES/NO, and
then press ENTER

to store the adjusted contents.
PROTECT YES (Initial setting)  PROTECT NO
Notes
• If YES is selected, the adjusted contents are protected and stored into the
preset buttons. When you want to store the parameter into a protected
preset button, “Replace NO/YES” can be selected.
• If NO is selected, the preset is stored.
• While perform this operation, all adjusted contents of Parametric EQ/
Graphic EQ and T.Correction will be stored in the preset buttons.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation (refer to
“Recalling the Stored Sound Field Adjustment Settings” on page 18).
Recalling the Stored Sound Field Adjustment
Settings
The stored Sound Field Settings contain Parametric EQ/Graphic EQ and
T.Correction settings that are stored in the preset memory.
1
After selecting any item of the Sound Field mode (e.g.
Parametric EQ), press any one of the
preset buttons (1
through 6) that has your desired characteristic in memory
to recall the stored settings.
2
Press the preset buttons (1 through 6) again to return to
the Sound Field mode.
Note
• While performing this operation, all adjustment contents of Parametric
EQ/Graphic EQ and T.Correction stored in the preset buttons will be
recalled.
Band-4 1.6 kHz~10 kHz
Band-5 10 kHz~17.5 kHz
Band-1 80 Hz
Band-2 250 Hz
Band-3 500 Hz
Band-4 1 kHz
Band-5 4 kHz
Band-6 8 kHz
Band-7 16 kHz