manualshive.com logo in svg

Alpha I AL905-SE, Инструкция по эксплуатации

Поделиться
Скачать
Alpha I AL905-SE Скачать руководство пользователя страница 41

Door Seal

 Check that this continues 

to make an air-tight seal and replace 
if necessary. Ensure that the new rope 
joint is also in the middle at the base 
of the rope seal channel.

 

Replacement 

door rope seal should be 12mm dia. 
See page 34

External Bodywork

 All external 

surfaces should be dusted with a soft 
cloth or light brush.
• Examine all paintwork for signs of 
wear and re-paint these areas using an 
appropriate heat-resistant aerosol paint. 

Warning: do not use the aerosol if the 
stove is alight or hot.

   

• When the aerosol paint has dried, 
apply traditional stove black polish to  
all painted surfaces
• Lightly oil the hinges and locking 
mechanism

Air Controls

 When standing down at 

the end of the heating season these 
should be left on the open position to 
allow some movement of air which will 
help avoid condensation and moisture 
building up inside the stove and flue 
system. These can be closed up to 50% 
if it gets too draughty.

Flue Pipe Connections 

Check all flue 

collar and pipe connections, where 
applicable, for any crumbling or missing 
fire cement seals. Remove any failed 
seals and re-seal using the appropriate 
heat-resistant fire cement.

Important 

In the interests of safety 

use only genuine Hi-Flame replacement 
parts which are readily available from 
your authorised dealer

 – see right. 

41

ALPHA SPARES SERVICE

In the interests of safety, only ever  
use genuine Hi-Flame replacement  
components. Once you have identified 
the component you need you can order 
it from your authorised Hi-Flame dealer 
– they will know your Alpha stove 
inside out!

Содержание I AL905-SE













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды