manualshive.com logo in svg

Alpha Radio 87A, Руководство по эксплуатации

Поделиться
Скачать
Alpha Radio 87A Скачать руководство пользователя страница 26

 

Page 26 

 

SAFETY 

There are lethal voltages in the Alpha 87A amplifier.  Special
precautions must be taken to allow for the safe completion of these 
modifications. 

  

1) Always unplug the amplifier from the 240 vac mains before
opening the case and doing any work on your 87A. 

  

2) The high voltage crowbar activates when the cover is removed 
and should eliminate any residual high voltage within the amplifier
but it is always prudent to short the high voltage to ground in the 
area of the tube plates or the plate RF choke with an insulated
screw driver as an extra precaution. 

  

  

 

 

 

 

3) Do not attempt to test the modifications with the cover removed 
since the built-in interlocks will not allow the amplifier to be 
energized. 

4) Do not defeat the interlocks as a means of testing the amplifier 
with the cover removed.  Proper operation of the amplifier requires 
that the cover be in place for shielding the digital circuitry from the 
radiated RF signal.

 

 

Alpha 87A User Manual Rev 2.0 

Содержание 87A























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды