background image

8

ALPHA COMMUNICATIONS®

• 42 Central Drive • Farmingdale NY 11735-1202

TOLL-FREE TECHNICAL LINE 1-800-666-4800

• Phone: 631-777-5500 • Fax: 631-777-5599

INTERNET WEBSITE: http://www.alpha-comm.com • EMAIL: [email protected]

THESE ARE LOW VOLTAGE DC POWERED CAMERAS AND THEY ARE POLARITY SENSITIVE.

THE POLARITY IS AUTOMATICALLY CORRECT WHEN THE POWER SUPPLY MODULE IS PLUGGED DI-
RECTLY INTO THE CAMERA USING THE FACTORY INSTALLED CONNECTORS. IF IT IS NECESSARY TO
EXTEND THE DISTANCE BETWEEN THE POWER MODULE AND THE CAMERA, CUT AND SPLICE THE
WIRE ON THE POWER MODULE ONLY. IF IT IS NECESSARY TO REMOVE THE POWER CONNECTOR OR
CUT AND EXTEND THE POWER CABLE, IT IS VERY IMPORTANT TO MAKE SURE THAT THE POLARITY
IS CORRECT BEFORE POWER IS SUPPLIED TO THE CAMERA. USE A METER TO CHECK THE POLAR-
ITY OF THE NEWLY SPLICED CABLE BEFORE CONNECTING IT TO THE CAMERA.

THE CENTER PIN MUST BE POSITIVE!

USE ONLY THE SUPPLIED POWER SUPPLY! POWER SUPPLY IS FOR INDOOR USE ONLY.

DO NOT REMOVE THE SERIAL NO. STICKER, AS THIS WILL VOID THE WARRANTY.

IF YOU ARE USING A PINHOLE STYLE CAMERA(s)

IN PLACE OF THE STANDARD S.T.R.

STYLE CAMERA(s)

CONNECT THE CAMERA(s) AS SHOWN ON THIS DIAGRAM,

AND NOT AS SHOWN ON THE PROCEEDING PAGES.

THESE CAMERAS ARE TYPICALLY USED WITH THE

NATURAL ANODIZED ALUMINUM,

STAINLESS STEEL AND POLISHED BRASS PANELS.

THESE CAMERAS ARE POWERED BY THEIR OWN

PLUG-IN POWER SUPPLY, WHICH IS SUPPLIED

WITH EACH CAMERA.

POLARITY MUST BE OBSERVED!!

Mini (Pinhole) Camera

(front view)

Twist-On (BNC) Connector
for RG59/U Coaxial Cable
(use model

CONN360

or

equivalent connector)

Plug-In Connector for
Model

SS12P

12VDC

Power Supply (included)

IMPORTANT INFORMATION AND

WARNING

:

Содержание VH30AK









Отзывы: