Almemo 2190-2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 24

Almemo 2190-2 Скачать руководство пользователя страница 21

9. ELECTROMAGNETIC COMPATIBILITY

The measuring instrument ALMEMO

®

2190-2 meets the electromagnetic

compatibility (EMC) safety requirements specified in the relevant CE directive
issued by the council for the alignment of legal regulations of the member
states (89/336/EWG).
The following standards have been applied for the evaluation of the product:
EN 50081-1:1992
EN 50082-1:1992

IEC 801-2 8kV, IEC 801-4 1kV
IEC 801-3 3V/m: deviation<100

µ

V

The following notes must be observed when operating the instruments:
1. If the standard sensor cables (1.5m) are extended it must be considered that the

measuring lines are not guided together with power mains and that they are
appropriately shielded to protect against any coupling of disturbance signals.

2. If the instrument is operated within strong electromagnetic fields an additional

measuring error must be expected (<50

µ

V at 3V/m and 1.5m thermocouple

transducers). After the irradiation the device operates again within the specified
technical data.

ALMEMO



2190-2

21

Electromagnetic Compatibility

«
...
19
20
21
22
23
...
»

Содержание 2190-2

























Отзывы:

Нет отзывов