Allstyle 4AC13018ASA1 Скачать руководство пользователя страница 1

4AC 14* ASA1  SERIES

R-410a  CONDENSING UNITS

INSTALLATION GUIDE

ATTENTION, INSTALLER!

After installing the system, show the user how to turn off 

electricity to the unit.  Point out control and switch locations 

for turning off electricity.  Make sure the user understands 

the importance of following all safety precautions, including 

what could happen if they don’t.

Keep the following documents in a safe, accessible location.  

Tell the user where these documents are located:

•  Installer’s Information Manual

•  Parts List

•  Warranty Information

While these instructions have been written as accurately 

and thoroughly as possible, they may not cover every 

system variation or contingency.  Questions of interpretation 

may arise.  For more information, solutions to particular 

problems or clarification, contact your local distributor or the 

manufacturer.

ATTENTION, USER!

Your equipment installer should give you the important 

documents listed above.  You should become familiar 

with these instructions, as it will be helpful in avoiding any 

needless service costs or operational problems.  Keep 

these instructions as long as you keep your equipment for 

future reference.  If any of the documents are missing or 

illegible, contact your installer or equipment manufacturer 

for replacement.

Throughout this manual, when we use the word “you” we 

refer to the qualified service technician who is responsible 

for application, installation, and service of your equipment.

While these instructions are addressed primarily to the 

installer, useful maintenance information is included.  Have 

your installer acquaint you with the operating maintenance 

requirements.

 

    

WARNING:

   Individuals who install this equipment, must have the training and experience necessary 

to install comfort air conditioning appliances.  Before performing any work on this equipment, the power supply 

must be turned off at the household service box.  Improper installation could void the warranty;  create a hazard, 

resulting in the possibility of damage, injury or death.

   

  

R

-410

A

816080 B

Содержание 4AC13018ASA1













Отзывы: