background image

POEFE24TV2 User Manual 

Alloy Computer Products Pty Ltd Copyright ©2012 

SAFETY PRECAUTIONS 

Read the following information carefully before operating the device. Please follow the 
following precaution items to protect the device from risks and damage caused by fire and 
electric power: 
 

 

Use the power adapter that is included with the device package. 

 

 

Pay attention to the power load of the outlet or prolonged lines. An overburdened 
power outlet or damaged cords and plugs may cause electric shock or fire. Check the 
power cords regularly, if you find any damage, replace it at once. 

 

 

Proper space for heat dissipation is necessary to avoid any damage caused by device 
overheating. The ventilation holes on the device are designed for heat dissipation to 
ensure that the device works normally. Do not cover these ventilation holes. 

 

 

Do not put this device close to a place where a heat source exits or high temperature 
occurs. Avoid placing the device in direct sunshine. 

 

 

Do not put this device close to a place which is damp or wet. Do not spill any fluid on 
this device. 

 

 

Please follow the instructions in the user manual/quick install guide carefully to 
connect the device to your PC or other electronic product. Any invalid connection 
may cause a power or fire risk. 

 
Do not place this device on an unstable surface or support. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 

 

 

Содержание POEFE24TV2














Отзывы: