background image

ALL168255 QIG English 

ALL168255 Quick Installation Guide      © 2012 ALLNET GmbH    All rights reserved          Page 12                                             

 

 

Konformitätserklärung 

Declaration of Conformity

 

Hersteller / Manufacturer:

 

ALLNET GmbH 

Produkt / Product:

 

ALL168255 

Typ / Type:

 

500Mbit    Powerline   

 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 

 

 

 

Germering, August 28, 2012

 

 

Getestete Normen: 
Tested Standards:

 

EN 55022:2010 

CISPR/I/257/CD:2008 

EN 61000-3-2:2006+A2:2009 

EN 61000-3-3:2008 
 

EN 50412-2-1: 2005

 

IEC 61000-4-2:2008 

IEC 61000-4-3:2010 

IEC 61000-4-4:2004+A1:2010 

IEC 61000-4-5:2005 

IEC 61000-4-6:2008 

IEC 61000-4-8:2009 

IEC 61000-4-11:2004 

 

EN 60950-1:2006+A11:2009+A1:2010+A12;2011 

This equipment is intended to be operated in all countries. 

 

 

 

This  device  has  been  tested  and  found  to  comply  with  the  stated 

standard(s), wich is(are) required by the Council Directive of 2004/108/EC. 

The  test  results  are  indicated  in  the  test  report  and  are  applicable  only  to 

the tested sample identified in the report. 

Address:   

 

Allnet GmbH 

 

 

 

Maistraße 2 

 

 

 

82110 Germering 

 

 

 

Germany 

E-Mail: 

 

[email protected]

 

 

 

 

[email protected]

 

 

Phone: 

 

+49 (0)89 894 222 22 

 

Fax:   

+49 (0)89 894 222 33 

Содержание ALL168255













Отзывы: