Allmand Maxi-Heat Series Скачать руководство пользователя страница 21

Страница: 21 / 42

Installation Instructions for Installing the

Slip-Lock Duct Connectors (PN #848974)

Heater Section – Inner Ring

1. Line up the receiver section (ring with slots) inside the heater flange and slide it in to where the small

rounded ridge (approximate center of connector ring) is just inside the outer edge of the heater flange. This

leaves 11/16” of this inner ring exposed and will allow the compartment door to close freely. Note: Make sure

that this alignment remains constant all the way around the outer edge of the flange.

2. Mark the locations of the (3) 3/16” holes and remove the receiver section from the heater flange. Using a

center punch, make a dimple in the center of each mark and drill each hole out using a 3/16” drill bit.

3. Re-install the receiver section into the heater flange and connect it (large head inside heater flange) using a

pop-rivet gun and (3) 3/16” pop-rivets.

Duct-Work Section – Outer Ring

1. Slide the end-cuff of the ducting over the larger outer ridge and stop when the cuff makes contact with the

small inner ridge (approximate center of connector ring). This leaves 1” of the outer ring exposed. Note:

Make sure that this alignment remains constant all the way around the outer ring.

2. Using a scratch awl, poke a hole through the ducting at the location of each of the (3) 3/16” holes and attach

the ducting (large head on outside of duct-work) to the outer ring using a pop rivet gun and (3) 3/16” pop

rivets

3. Take the 16” screw clamp (PN #848176) and install it right over the top of the (3) 3/16” rivets on the outer

ring and tighten down securely on the ducting. Note: Make sure that this alignment remains constant all the

way around the outer ring before tightening.

4. Your ductwork is now ready to be connected to the heater unit.

3/16” Pop Rivet

Head Inside Flange

(Body Out)

11/16”

1”

3/16” Pop Rivet Heads

directly under screw clamp

11/16”

1”

Not

for

Reproduction

Содержание Maxi-Heat Series











































Результаты поиска

Содержание Maxi-Heat Series

Отзывы:

Похожие инструкции для Maxi-Heat Series

Бренды по названию

Популярные бренды

Allmand Maxi-Heat Series, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Maxi-Heat Series

Отзывы:

Похожие инструкции для Maxi-Heat Series

Бренды по названию

Популярные бренды