Allied 80G1UHEX Series Скачать руководство пользователя

Страница: 24 / 32

507651-01

Page 24 of 32

Issue 1907

Red LED Flash Code

Diagnostic Codes / Status of Furnace

Off

No power to control or board fault detected

Heartbeat

Control powered - displayed during all modes of operation if no errors are detected

Continuous Rapid Flash

Call For Heat / Burner Operation

1 flash

Reverse line voltage polarity

2 flashes

Improper earth ground

3 flashes

Burner failed to light, or lost flame during heating demand

4 flashes

Low flame signal - check flame sensor

5 flashes

Watchguard - burner failed to light, exceeded maximum number or retries or recycles

6 flashes

Not used

7 flashes

Primary or secondary limit open or Watchguard mode - limit switch open longer than 3 minutes

8 flashes

Rollout switch open

9 flashes

Pressure switch failed to close of opened during heat demand

10 flashes

Watchguard - pressure switch opened 5 times during one heat demand

11 flashes

Pressure switch stuck closed prior to activation or combustion air inducer

12 flashes

Flame sensed without gas valve energized

13 flashes

Low line voltage

A ”Heartbeat” is indicated by a ”Slow Flash” - 1 sec on 1 sec off, repeating

Error codes are indicated by a “rapid flash” - the LED flashes X times at ½ second on ½ second off, remains off for 3 seconds then

repeats.
Last 10 error codes are stored in memory including when power is shut off to the unit. - To recall, press and release button, most

recent will be displayed first, LED off for 3 sec, then next error code is displayed, etc. To clear error codes, depress and hold button

longer than 5 seconds.

Table 7.

Figure 24. Integrated Control

(Automatic Hot Surface Ignition System)

Red LED

Recall Button

Blower Off Delay

1/4” Quick Connect Terminals

120 HUM

Humidifier (120 VAC)

LINE

Input (120 VAC)

XFMR

Transformer (120 VAC)

CIRC

Indoor Blower (120 VAC)

EAC

Electronic Air Cleaner (120 VAC)

NEUTRALS

Neutral Terminals (120 VAC)

HUM 24

Humidifier (24 VAC)

3/16” Quick Connect Terminals

COOL

Blower - Cooling Speed (24 VAC)

HEAT

Blower - Heating Speed (24 VAC)

FAN

Blower - Fan Speed (24 VAC)

PARK

Dead terminals to park all speed taps

Flame Sense

24 COM

Common (24 VAC)

Содержание 80G1UHEX Series

































Результаты поиска

Содержание 80G1UHEX Series

Отзывы:

Похожие инструкции для 80G1UHEX Series

Бренды по названию

Популярные бренды

Allied 80G1UHEX Series, Руководство по установке

Результаты поиска

Содержание 80G1UHEX Series

Отзывы:

Похожие инструкции для 80G1UHEX Series

Бренды по названию

Популярные бренды