Allied 4AC13 Скачать руководство пользователя страница 1

507043-03

Page 1 of 9

Issue  1337

These instructions must be read and understood completely before attempting installation.

4AC13/14 SPLIT SYSTEM AIR CONDITIONER 

INSTALLATION / STARTUP INSTRUCTIONS

/HOMEOWNERS INFORMATION MANUAL

Manufactured By

Allied Air Enterprises LLC

A Lennox International Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

 (P)  507043-03

Improper Installation, adjustment, alteration, service or

maintenance will void the warranty. The qualified installer 

or agency must use factory-authorized kits or accesories 

when modifying this product. Refer to the individual 

instructions packaged with the kits or accesories when 

installing.

  CAUTION

Installation or repairs made by unqualified persons can 

result in hazards to you and others. Installation MUST 

conform with local building codes and with the National 

Electric Code NFPA 70/ANSI C1-1993 or current edition 

and Canadian Electrical Code Part 1 CSA .

  WARNING

These instructions are intended as a general guide 

and do not supersede national, state or local codes in 

any way.

These instructions must be left with the property 

owner.

  NOTE

Safety Precautions  ...............................................2

Unit Location & Installation ....................................2

Rooftop Installation & Recommendations .............3

Indoor Coil Piston Selection ..................................3

Refrigeration Line Sets ..........................................3

Installation of Line Sets .........................................4 

 

Leak Check............................................................4 

 

Evacuating & Charging ..........................................4 

*P507043-03*

TABLE OF CONTENTS

Electrical Connections  ..........................................5

Control Wiring ........................................................5

Start-Up Procedure................................................5

Adjusting charge ....................................................5

Single Phase Wiring Diagram.............................7/8

Homeowner’s Information .....................................9 

These units are designed for use in residential and  

commercial type buildings. Units should be installed  

with combinations listed in the Air-Conditioning, Heating 

and Refrigeration Institute (AHRI) Directory of Certified 

 

Products. Refer to http://www.ahridirectory.org . 

 

Before installation, inspect the unit for shipping damage. 

If damage is found, notify the transportation company  

immediately and file a concealed damage claim.

Содержание 4AC13










Отзывы: