Allied Vision Technologies Prosilica GC1280 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

Allied Vision Technologies Prosilica GC1280 Скачать руководство пользователя страница 3

GC1280 User Manual

70-0039A-C

AVT Inc.

1

Introduction

The GC1280 series of cameras are 27 frames per second, mega-pixel, Gigabit Ethernet

cameras

based on the Cypress IBIS5B-1300M CMOS sensors with snapshot shutter capability.

Precautions

READ INSTALLATION GUIDE CAREFULLY.

This document contains specific information which is necessary for the correct operation and
treatment of this product.

DO NOT OPEN THE CAMERA. WARRANTY IS VOID IF CAMERA IS OPENED.

This camera contains sensitive components which can be damaged if handled incorrectly.

KEEP SHIPPING MATERIAL.

Poor packaging of this product can cause damage during shipping.

VERIFY ALL EXTERNAL CONNECTIONS.

Verify all external connections in terms of voltage levels, power requirements, voltage polarity,
and signal integrity prior to powering this device.

CLEANING.

This product can be damaged by some volatile cleaning agents. Avoid cleaning the image sensor
unless absolutely necessary. Please see instructions on sensor cleaning in this document.

DO NOT EXCEED ENVIRONMENTAL SPECIFICATIONS.

See environmental specifications limits in the Specifications section of this document.

Warranty

Prosilica  provides  a  2  year  warranty  which  covers  the  replacement  and  repair  of  all  Prosilica
parts  which  are  found  to  be  defective  in  the  normal  use  of  this  product.    Prosilica  will  not
warranty parts which have been damaged through the obvious misuse of this product.

«
1
2
3
4
5
...
»

Содержание Prosilica GC1280





























Отзывы:

Нет отзывов